PCE23NGTDFSS General Electric Refrigerator - Instructions

New parts just snapped in place. Perfect fit.

I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do

I put kickplate on refrigerator and use 2 sheetrock screws and drill to attach. Done in 5 minutes.

Went exactly by the video. Perfect job, you send the installation video with the part. You watch the video before or during, goof proof, took longer to disassemble than to replace the part.

replaced the water filter head and water lines which were fairly easy. Glad Partselect had was I was looking for and it arrived quickly.

removed ice bucket from frig. removed screws to dis assemble the box to get to the auger assembly,removed stripped nut replaced reassembled be care not to let the rest of the assembly fall from auger there are a lot of blades and spacers to try to get back to proper position.

Turn-off water and disconnect main water line to inlet-tube.
Removed lower-back panel of the fridge with a screw driver and disconnected the hose with a small wrench to the main fridge water valve.

On th top-left, back of the fridge, removed screws to the small plate where the hoses enter for the water filter. In the fridge, removed the water filter, then removed the plastic panel above the filter - it snaps out. There are two screws to remove, then grasp and pull the assembly and hoses out. reverse the process for an easy install.

I was not able to put the small plate onthe back, top-left of the fridge back on. It's a tight fit and I didn't want to pinch the lines. Not doing that, though, may limit how your fridge rolls back to where it was, because the lines will stick-out a couple of inches.

I made my wife fix it.

We had to pop out the insert module that was cracked, which was fairly easy. Then we needed to insert the new insert module. It was necessary to pull the side of the shelf while trying to snap in the new part. It was a bit difficult, but we finally were successful and we are very pleased.

remove light cover then remove 4 screws holding light fixture in place pulled out fresh food inlet cover and had to removed 2 more screws at bottom of cover then unplug electrical connector. replace with new one then replace all 6 screws and light cover done. so far its been working great no more freeze ups.

I had to take off the back lower grate which was roughly six 1/4 screws. Disconnect the water lines to the ice maker and the filter manifold. Remove the manifold from the inside of the refrigerator by removing two 1/4” screws. Pull the manifold and line out from the inside of the refrigerator and reverse the process for the replacement.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Ordered ice crusher dispenser cover removed 3 screws and face plate of ice crusher was easily replaced and again working like new

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

as soon as i put the new piece in there was plenty of water for full size ice cubes, which it has not done in 3or4years.i was really glad with the speedy delivery of the parts roy anderson