ZSEP420DWASS General Electric Refrigerator - Instructions

Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

Show installation!

you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.

Turns out it was only the frozen water that thawed when I unplugged the fridge for 24 hours.
New part returned, not used.
Service was excellent.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

removed the back cover, removed one srew that held the valve, disconnected water lines, and installed the new valve. Piece of cake!

My GE SideBySide fridge stopped making ice. The green LED light on the icemaker was not blinking. The water dispenser worked fine. Fridge is only 5 years old. Freezer temp set at 7 degrees...fridge at 37 degrees. I have been using these temps since new. GE hotline suggested freezer temp should be at zero degrees. That did not work. Second call suggested an airflow issue within the freezer...there should be 1 inch space between food and back wall. Still no ice. The water valve looks to be the issue. I ordered it and got it in 2 days. Valve is in the back bottom, refridgerator side. Push the white collars around the water hoses...Then pull the hoses out. An adjustable wrench removes the nut for the inlet hose. Disconnect 2 electrical plugs. Be sure to push the water hoses fully into the new valve. I pulled the white collars out a bit to insure a tight fit. I was surprised at how simple this was to install. As it turns out, I was still getting no ice. I ordered a new ice maker and now I'm getting ice. The icemaker was EVEN EASIER to install.

Watched some videos on youtube after typing in : refrigerator noise, and my model # (in search bar.) Found a video after determining my problem of a gentleman from partselect replacing the evaporator motor. Pretty simple job from video so I went for it ordered parts from them( I fixed the inlet valve on my dishwasher bfore with partselect before). I would call the job easier than it looks. But you need common sense and simple tools and some experience with nuts and bolts and wires. There is one bolt tucked up high under ice maker you may need a right angle nut driver or 1/4 right angle ratchet.(video pointed out). Thanks for video and quality GE parts. I now have a quiet kitchen and great room, with just a low db constant white noise like new.

Used a YouTube video with step by step directions, this made the repair very easy.

Disassembled ice-maker, noting what screws went where, what direction ice release control arm pointed, and noting how the control arm spring was mounted. The door assembly comes off first followed by the circular assembly that houses the ice door and last grinding arms. It is quite easy see how it comes apart as you look at the screws. Remove the screw holding the back end of the control arm and note the spring position. The control arm needs to be turned to line up notches to pull it thru a faceplate hole while rotating the arm about the "U" that is on the outside of the faceplate in the door housing. There is a retaining clip holding the rotating impeller to remove to complete the dis-assembly. Use vinegar to clean rust out of bin and other parts around the faceplate. Assemble the unit in the reverse order to complete the job.

I put the water hoses out the valve and put the hoses back in new valve after that put the valve in the same place with the nutdriver. When refrigerator take the temperature inside, the ice began really easy. Thank you.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.