PIG23MIMFFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Indian Trail, NC
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
5/16" tubing to chilled water dispenser cracked
Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Ponce Inlet, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace solenoid on ice door
remove the front plate. use screwdriver to pry the cover off from the bottom of the cover, remove the wiring from the front cover.remove the 4 screws and pull out the shute. remove three screws from the solonide and replace . very easy fix. save yourself $100.00 labor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from hatboro, PA
- Parts Used:
- WR62X10055, WR17X11653, WR23X10783, WR17X10706, WR02X10585
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Flapper is stuck open
There are three holes under the front panel in which you push a very small screwdriver in and the front panel comes off.In back of the panel is another panel with 4 screws .1 at each corner.Remove the 4 screws and that will come off exposing the working parts that need to be replaced.This is also a good time to clean anything you can get to in that area.It is very important to remember how everything came out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Holly Springs, NC
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Fridge getting warer and warmer
remove back panel inside fridge freezer side, everything frosted, unplug and used a hair dryer
1. Took out defrost heater and the bottom and tested (per this site) tested OK.
2. Then looked at the defrost thermostat, it was swollen with the top coming off. so i new it was bad
3.clipped and stripped the 2 wires, spliced in the new one with wire nuts and sealed them with silicone. All better
1. Took out defrost heater and the bottom and tested (per this site) tested OK.
2. Then looked at the defrost thermostat, it was swollen with the top coming off. so i new it was bad
3.clipped and stripped the 2 wires, spliced in the new one with wire nuts and sealed them with silicone. All better
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randall from coopersville, MI
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
refriderator not cooling consistetly
1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Can of fruit fell from shelf and broke the switch cover.
Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from NAPLES, FL
- Parts Used:
- WR71X10973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Not a problem at all.
I took out the old bins just as when you take them out to clean them. And then I replaced the bins with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from UPPR MARLBORO, MD
- Parts Used:
- WR14X10059
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber gasket had torn, and super glue only provided a temporary solution.
1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene from Springfield, IL
- Parts Used:
- WR17X11497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
plastic parts came out of ice dispenser
Removed icemaker from freezer, remove covers allowing access to dispenser. In the next step I removed the auger and broken shield as one assembly. With assembly out of icemaker it was a simple task of taking the broken shield off of auger and putting the new one on. Reassemble in reverse order as removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- doyle from kingston, WA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
freezer was freezing up.
took the back off and defrosted with a hairdryer. disconected the part pulled the part out cut the wires. put the other part on and instaled it. put it back together and it seems to be working just fine. thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Georgetown, TX
- Parts Used:
- WR23X10783
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Water dispenser not dispensing water
I went to the internet and found parts select web site. Saw all of the possible fixes for my problem and read all of the other repair stories. My story actually became a journey that is still continuing. I first changed the water filter, but still no water at the dispenser. I next disconnected the coupling at the bottom of the freezer door that carries water to the dispenser and when the dispenser was depressed, water flowed at the coupling, but not at the dispenser. After reconnecting the coupling, I turned the freezer setting to 1 for 4-5 days, but still no water at the dispenser (possibly the line was frozen, but we had recently been away for a week and the water dispenser still supplied water at a freezer setting of 4). Now I am at the point of the journey into replacing parts one at a time to get water. First I ordered the dual water valve for the ice maker and water dispenser. I replaced this valve with instructions from Parts Select and still no water at dispenser. Next I ordered and replaced the switch at the dispenser lever and still no water. Next was the solenoid attached to the ice door, ordered, replaced and still no water at dispenser. I am now at the final part in this repair and that is the $132 circuit board. So I will be ordering this part soon and hopefully that will fix the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from HEBER, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
condenser icing refrigerator warm freezer ok
follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JIAN from Brooklyn, NY
- Parts Used:
- WR60X10307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Fan not working
Take off all , then install.. following the version..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from LATHROP, MO
- Parts Used:
- WR17X11440
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Tank was leaking.
Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fernando from SOUTHAMPTON, NY
- Parts Used:
- WR17X11440
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Water Tank Cracked
First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use
Was this instruction helpful to you?
Thank you for voting!