GSK25LHSACCC General Electric Refrigerator - Instructions

I got the model # off the fridge, ordered the part online. The part was fairly cheap and was at my house 2 days after I ordered it. It was the exact part and I installed it in about 15 minutes and everyting worked out fine and easy and cheap, under $15 total to fix the issue. All I needed to do was use a flathead screwdriver to "pop" out the old switch, remove the 2 wires off the wire connection points, put the wires on the new switch and push it back into place. easy. Great place to get exact parts and fast shipping.

I located the light switch at the bottom of the area where the door closes. I just popped it out with a small screwdriver and installed the new switch. A 2 wire connecter and small clip is all there is to it.

Really simple... broken light switch easily removed with flat edge screw driver. Once removed unplug and plug new one in and good to go.

Replaced Defrost Thermostat. Tricky removal of light fixture cover and evaporator cover. Light cover screw removal is not intuiitive and the eveaporator cover tabs are not easy AT ALL to remove.Once they are removed, simply 2 screw removal of rear panel.

Had to unscrew screws holding cooling coils to gain access to thermostat mounted on a coil in rear.

Simkple matter to cut wires, remove old thermostat and splice replacement back on. Found it simpler to re-mount thermostat on top coil greatly simplifying process.(Why didn't they place the original unit in this much more accesible place?)
Re-attach coils to rear wall replace rear panel, light fixture cover and evaporator cover.

Refrigerator has been running fine this past week.

Received parts NEXT DAY! FANTASTIC!

Removed light cover, found 2 screws in front and rear of light area.Remove screws and you can unplug light to get out of way, but not necessary. Next pop off plastic cover with flat head screw driver and remove the two screws under cover. Next pull cover off water filter and remove water filter this will give you room to slide inlet cover out. Install plastic cone provided by in new kit. Next slide new cover over cone and re-install bottom screws, however leave them loose in order to adjust for the following screws to line up. After all screws and plugs are in place snug all screws. Replace light cover an install water filter and cover. You are done.

remove light cover then remove 4 screws holding light fixture in place pulled out fresh food inlet cover and had to removed 2 more screws at bottom of cover then unplug electrical connector. replace with new one then replace all 6 screws and light cover done. so far its been working great no more freeze ups.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

I got the wrong switch before so just need to put the right 1 in. Super easy, pop off old, plug in new, click back into place. Done. REALLY REALLY EASY for anyone to do

I made my wife fix it.

I followed the onsite video and had no problems. Shut off refrigerator, removed storage trays and bind, removed the rear panel under the light, identified the orange and pink electrical wires and cut them. Spliced the new wires of the thermostat with refrigerator wire and capped them, applied electrical tape to insure no moister makes contact with wires. Replaced rear panel and storage racks and bind. Plugged in the refrigerator and it is operations like new. I was about to purchase a new refrigerator for $ 1,300.00 and the thermostat costed $ 13.00. What a Christmas present!

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Knew the switch was bad. Researched on the internet how to fix. Used a steak knife to pop the old one out, changed the contacts to the new switch and popped it back in. It took longer to open the box than it did to replace the switch. And the part arrived 2 days after I ordered it.

It was so darn easy! Took less then 10 minutes to fix. Self explanatory no instructions needed! Very cool!

removed 6 screws and repaced cover.

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.