Models > GDS20KCSCWW > Instructions

GDS20KCSCWW General Electric Refrigerator - Instructions

Jump to:

All Instructions for the GDS20KCSCWW
91 - 105 of 273
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Kirk from Rio Rancho, NM
Parts Used:
WR55X10942C
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Ice/Water dispenser would not work and refrigerator stopped cooling
The first and most important step was to diagnose the problem. To do this I found the Parts Select website and the part I thought was the problem. The previous repairs stories helped me to pin point the problem. The mother board came within a couple of days. All I had to do was take the back plate/guard off, unplug the connectors in the back, unclip the mother board and then do the reverse over again. The only problem was the ground wire. I had to take the one off that came with the part and switch it out with the old one, because it would not connect to my refrigerator. This was fairly simple and in about 30 min. I was done and had our refrigerator back. Luckily we had another in the garage as a back up so we didn't loose any food.

Thanks Parts Select
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joseph from Middletown, DE
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
refrigerator clicking noise
removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Hopewell Junction, NY
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Fridge/Freezer bad temps and clicking sounds from rear
Found out via searches that the most likely failed part was the Main Control Board. A simple repair with basic tools and a HUGE savings. Thanks to everyone here for the posts.

PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Baldwin, NY
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Refrigerator wasn't cooling
Very simple fix by replacing the mother board. Your "how to" video made the repair even easier. The appliance repair estimate was over $400. I saved over $200. I already recommended your site to several other people. Thanks for making it so easy
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Trevor from Brooklyn, NY
Parts Used:
WR55X10942C
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Refrigerator failed to get cold.
the new board was more complicated than the old, however the install instructions seem to have anticipated this. It works for mow. thanks for inquiring'
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
QUOC-LOC from LYNN HAVEN, FL
Parts Used:
WR55X24064
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
lisa from houston, TX
Parts Used:
WR55X10942C
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Refrigerator kept turning off and on
I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from Floral Park, NY
Parts Used:
WR55X10942C
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
first water on door would shut off then refridgerator shut down completly unpluged and pluged back in and it made clicking noise the light always stayed on
was not home when part came so my wife installed it enough said
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Loomis, CA
Parts Used:
WR55X10942C
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Ice and water dispenser wouldn't work- light dimmed and surged each time it was activated.
First, the part arrived very quickly- 2days (FedEx). Removed the back panel, began pulling multi-prong plugs from the old board. To remove the plug that came out laterally (power wires?), I used a thin screwdriver to press the retaining clips on the side of each pin (4 white) holding the circuit board in place and pulled it out for clearance, then wiggled the multi plug free from the board. [I didn't put a lot of pressure on the board while pulling these plugs- 'cause if the new board didn't work, I'd still have the old one.]

Installation was pretty much the reverse of all the steps above. Thankfully, this unit did not have a bottom freezer as two steps in the instructions would have made it riskier.
Once plugged in, I listened for the fan and compressor to kick-in, didn't hear them (was concerned at first), but the dispenser worked ("yea!")- both crushed and cubed ice. The water worked also and it's been running fine for a couple of weeks now. After checking the temp settings they seemed more stable, the fan and compressor kicked in after a few minutes, and the ice-maker is working better than before (fills more quickly). Also, it seems to run less which makes me think I've been wasting electricity while the old control board was bad. Who knows what temps it was trying to reach on each side?
Not that hard to repair, but read the instructions 'very' closely so you don't do something (like cut a wire) that doesn't apply to your fridge. Tim
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Adam from Morgantown, WV
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Everything thawed out
I ensured that the refrigerator was unplugged from the power, removed the main board enclosure cover, carefully unplugged the wiring connectors from the board, released the 4 plastic standoffs with needle nosed pliers by gently squeezing the ends and removed the board.
I placed the new Main Control Board on the standoffs, carefully re-connected the electrical connectors, ensuring that the plugs were mated correctly, replaced the board enclosure cover and powered up the refrigerator to verify operation of the compressor, fans and controls.
Once verified, I unplugged the refrigerator from the power, removed the access cover to the compressor and condenser and carefully cleaned all dust and lint from the back and underside of the refrigerator before replacing the cover and putting the refrigerator back into service.
The cleaning will improve the efficient operation of the refrigerator.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Les from Sierra Vista, AZ
Parts Used:
WR55X10942C
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Fridge failed to cool
Moved fridge out from wall. Unplugged. Removed circuitboard cover 6 screws?). Replaced circuit board (showed burn spots on back side). Replaced cover and plugged back in.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wenfang from Farmington Hills, MI
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
My refrigerator produces no cold
I found a burn solder on the main board.
replace it. works again.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Albert from Alger, MI
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Ice/water dispenser inoperative
Removed small panel on back of refrigerator, lower right hand side as you face the back. Removed old mother board and installed new one per provided instructions. Ice/water dispenser operation returned to noraml. The only tricky part is removing the motherboard because it's held in with platic clips that have to be pinched with pliers in order to slide the motherboard over them. Look carefully and you'll see which way to pinch them.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Belvidere, NC
Parts Used:
WR55X10942C
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
refrigerator not working
Having been in the h vac field for thirty years,I started looking for the defrost timer and found the circuit board. I went on-line and found PartSelect. The site was very helpful in helping me to find the part I needed.The clips were a little hard to get off the old board, but besides that the installation was pretty easy.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Hockessin, DE
Parts Used:
WR55X10942C
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
No Compressor /but thermometer calling
Replaced circuit board / fixed problem
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GDS20KCSCWW
91 - 105 of 273