GCE23YBTBFWW General Electric Refrigerator - Instructions

Pulled out broken switch with flat head screwdriver and replaced with replacement part purchased from partselect. Easily plugged in new part and replaced.

Removed the dairy shelf from the refrigerator door,slid the clear plastic dairy door/cover into the shelf and replaced the shelf onto the refer door.

I used the pliers to hold switch while I got screwdriver under the switch then pulled out. I THEN unplugged old one and plugged in New one and put it back in place.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

I couldn’t repair the problem because the part that came did not have the clips to crimp on the end that go into the modular connection,

had to remove ice maker and several panels to get to the fan. wires for fan encapsulated so had to cut old and new wires then solder them together while working inside the small freezer area. not too bad all in all took about an hour to get it done. no more wind thru the trees noise and is working fine

Unplugged the freezer. Then I gained access to the fan: remove the top freezer rack, remove the ice tray, remove the air flow manifold(needed to unscrew some screws), remove the manifold over the fan and cooling element. I unscrewed the fan mounting bracket. The fan motor's wires are plumbed through some plastic that i would have had to remove, so I decided instead to cut the wires and splice in the new fan motor. Then I put everything back together - the new motor works fine and doesn't make the whining noise.

Remove all shelves and back duct work in refrigerator section. Remove 4 screws and electric door / blower section. Part was exact replacement. Refrigerator is working perfectly.

1) remove the ice bucket. 2) remove light cover and bulb. 3) remove back panel with 2 screws. 4) remove fan shield. 5) unlug 2 elec connections. 6) remove fan housing. 7) extract wiring grommet and use exacto knife to slice thru grommet along the length of it to release wires. don't cut light wires. 8) cut up old fan/light electrical plug to free wire nubs for light. 9) install nubs in new fan plug. 10) remove old fan motor, pull blades. 11) install blades on new fan moter and install fan into housing. 11) reinstall

Really easy

Poped whole switch out with flat head screw driver. Removed wires with needle nose players and held the wires so they wouldn't get pulled back inside fridge shell. Attached wires to new part like a plug. Lights ccame back put new switch back inside wall. Shut door

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

When the Part Select website predicted delivery in a couple of days, I doubted - I was prepared to wait a week or so. Incredibly, the part arrived the day after I ordered it. Replacing it was no problem, because the exploded view of the hinge area showed a clear and easy way to remove the broken part and slip in the new. It was just 2 inches of plastic, but if I hadn't found it so easily, the whole appliance would have been useless.

Item sat in a garage and needed to be thorougly cleaned of mold that grew in its 2 years off. I had to remove the doors to get them into my new house. The repairs went easy once I figured out how to put the doors back on. This website had excellent detailed schematic drawings. It was very easy to order the parts. I wanted to replace the handles on both doors beacause they didn't clean up at all. Once these handles are soiled, theyre impossioble to clean! So I replaced these parts, and it looks brand new. Thanks fo making everything so easy!