GDS20KBSDCC General Electric Refrigerator - Instructions

My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.

Pull fridge out. Pull the little 6 by 12 silver plate off on the back middle bottom of fridge. Disconnect the quick connects . Remove from 4 plastic pins. Them reassemble.

I found this failure at midnight, was able to determine loss of voltage at J2 Pin 3 to 4, causing the fan failure. Jumpering with a staple from Pin 5 to 4 allowed the evap fan to run from the condensor fan supply for the few days waiting for the part. Not pretty, but it saved the food. Running like that forced the evap fan to high speed, so I had to set the thermostats lower (higher temp)

1. To un-mount the board, use needle nose to gently squeeze plastic bayonets one at a time and lift that corner clear.
2. Mark each connector J1, J3, J4, J2, J5 to match the mark on the old board
3. Gently work each connector off, replace board, and re-land each connector. The new board will have a ground wire. Just trap the lug under the upper left cover plate screw..

I took the 3 screws off the cover that is in the back of the appliance, unpluged the plugs that attached to the circuit board pressed the 4 plastic pins that held the old board. Then I snapped the new board in place and pluged the plugs back into the new board. They will only go on one way so you cannot get the plug in the wrong place, job done appliance works fine. Thanks

Removed circuit board cover, unplugged l
Leads, rePlaced board, leads and cover. Done

Also watch the video. Super simple

I wouldn't have had a clue without your video. After the part was delivered, which was only in two days, I watched the video. The man explained everything perfectly, making our "fix" a breeze. It was great, I stood over my husband's shoulder, while he sat on the floor and told him what to do step by step. It couldn't have been easier. You guys are awesome!

Of course I had to order the filter and upon receiving it I installed the new one in about a couple of minutes. Even though my fridge doesn’t have a water dispenser it does make ice. Removed all the old ice from tray and disposed of it cause it was getting a bad taste to it. I let the tray fill up with ice once and disposed of the ice. After it filled up a second time I tasted the ice and had a very good clean taste. And my lesson is I need to replace filter at least once a year I think would be sufficient. That’s all there is to it, simple !!!

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Unplug electrical power to refrigerator. Disconnected electrical power to water valve, Disconnected water inlet and out let lines from valve. Remove screw holding valve on refrigerator, removed and replaced water valve with screw. Connected inlet and outlet water lines, turned on water and checked for leaks. Connected electrical power to water valve, plug in electrical power to the refrogerator. Ice maker tray fill, made ice.

Started with a visual inspection.
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....

Very simple fix by replacing the mother board. Your "how to" video made the repair even easier. The appliance repair estimate was over $400. I saved over $200. I already recommended your site to several other people. Thanks for making it so easy

Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks

Put bracket on workbench and hit two or three times with hammer. Glad I did not remove water inlet retainer from part, it can very easily be mistaken for a thread protector.

I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.

I ensured that the refrigerator was unplugged from the power, removed the main board enclosure cover, carefully unplugged the wiring connectors from the board, released the 4 plastic standoffs with needle nosed pliers by gently squeezing the ends and removed the board.
I placed the new Main Control Board on the standoffs, carefully re-connected the electrical connectors, ensuring that the plugs were mated correctly, replaced the board enclosure cover and powered up the refrigerator to verify operation of the compressor, fans and controls.
Once verified, I unplugged the refrigerator from the power, removed the access cover to the compressor and condenser and carefully cleaned all dust and lint from the back and underside of the refrigerator before replacing the cover and putting the refrigerator back into service.
The cleaning will improve the efficient operation of the refrigerator.