GDS20KBSDCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from RUSHVILLE, IL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
Water valve failed. Constant drip in ice maker.
Removed old valve easily. New WR57XI0033 valve is designed to mount on lower left, but on mine it has to mount on lower right. Had to drill two 1/32 holes in lower rail to mount the new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from melrose, IA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
deep freeze defrosting and frig. getting warm shortly after stoped cooling completley
Received main board in less than two days. back of frig. small panel removed 3 screws, removed cover exposing main board with needle plires squeesed 4 plastic tips to release board unpluged conectors, reinstaled new board, worked perfict. Thank you for your helpfull web site. Bob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from washington, NC
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
freezer would freeze then thaw
diagnosis, fan would run more than normal, compressor would only come on sometimes, check line voltage to the mother board (yes !!! a mother board with a relay for the compressor built onto it )! check the switched voltage out to the compressor. If a/c 115 in but no a/c 115 out while the fan is on replace the mother board. Remember this is a LIVE VOLTAGE TEST, BE CAREFUL HOW AND WHAT YOU TOUCH YOUR LIFE IS NOT WORTH SAVING A REPAIR BILL !!!
I suppose if if went long enough in this condition the result would be fan runs a lot but it does not get cold.
Hope this helps
God Bless
Captain Scott Cousins
I suppose if if went long enough in this condition the result would be fan runs a lot but it does not get cold.
Hope this helps
God Bless
Captain Scott Cousins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HECTOR from INGLESIDE, TX
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Faulty Motherboard
Disconnected power at outlet. Removed three screws from access panel. Disconnected six electrical connections, compressed three plastic retaining pins and removed board. Installed new board and reconnected connections, installed three screws on access panel and turned the fridge on. No more crazy evaporator motor noise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Yardley, PA
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer and refrigerator would get warm, followed by it getting cold again, doing this numerous times throughout the day.
After determining it was not a problem with the defrost cycle, ( this refrigerator had no separate defrost timer), I ordered the main circuit board with the hope that the relays built into it were hanging up and not properly turning on the compressor, (a chattering sound could be heard). Ten screws to take the access cover to the board off and a few connectors later and it was as good as new. Took about ten minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shelby from Sturgis, SD
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice and water dispensers were not working, Control board was making a clicking noise.
Disconnected power, removed screws from cover on back of refrigerator, unpluged wire connectors, squezzed four support fasteners and removed old board. Put new board on support fasteners, reconnected wiring, replaced cover, pluged power back in, turned controls back on. It wored fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Lewes, DE
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no water to icemaker
removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raul from Columbia, MD
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Control panel on the front door became was dead. Replace the Main control board was de solution suggested by a Technician.
I followed instructions in your video. at the beggining I hesitated because the original card had two fewer ports than the new one. but after a call to a Partselect representative I confirm that I had the right card. after that it was a matter of connet wires to the ports. 1 week later my refrigerator is running smooth. Thaks a to Partselect I have saved a bunch of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Vineland, NJ
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Circuit Board was clicking and refrigerator was not working properly
narrowed it down to the circuit board...removed cover panel after unplugging frig. read directions thouroughly.... removed cables attached to old board. this is the tricky part removing the board from the plastic clips....broke two pulling old board off popped new Board onto remaining plastic mounting clips and reattached cables plugged frig in and got a shock as my shoulder touched the board. everything seemed to be working and but cover back on....viola all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Stevensville, MD
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Continuous clicking noise, compressor was not running
Removed the old control board at the rear of the refigerator, installed the replacement board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirk from Rio Rancho, NM
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice/Water dispenser would not work and refrigerator stopped cooling
The first and most important step was to diagnose the problem. To do this I found the Parts Select website and the part I thought was the problem. The previous repairs stories helped me to pin point the problem. The mother board came within a couple of days. All I had to do was take the back plate/guard off, unplug the connectors in the back, unclip the mother board and then do the reverse over again. The only problem was the ground wire. I had to take the one off that came with the part and switch it out with the old one, because it would not connect to my refrigerator. This was fairly simple and in about 30 min. I was done and had our refrigerator back. Luckily we had another in the garage as a back up so we didn't loose any food.
Thanks Parts Select
Thanks Parts Select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from Middletown, DE
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
refrigerator clicking noise
removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Brooklyn, NY
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
Refrigerator failed to get cold.
the new board was more complicated than the old, however the install instructions seem to have anticipated this. It works for mow. thanks for inquiring'
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK M from EASTON, PA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Ice Maker was not working
1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hopewell Junction, NY
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge/Freezer bad temps and clicking sounds from rear
Found out via searches that the most likely failed part was the Main Control Board. A simple repair with basic tools and a HUGE savings. Thanks to everyone here for the posts.
PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.
PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.
Was this instruction helpful to you?
Thank you for voting!