RSK25LCMACCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from GROVELAND, FL
- Parts Used:
- WR02X10821
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Slide control was broken
Simply slide new control slide through slot from front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- otis from LAND O LAKES, FL
- Parts Used:
- WR72X10169
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Left side freezer ice bucket rail broken.
Used nut cracker to take out 2screws. Had to take one screw from icemaker, raise it up slightly to get nutcracker accessibility. Price of cake. Ofelder
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jamie from WINCHESTER, CA
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Side by side fridge and freezer both hot warm and the inside back panel of the freezer all frosted
As per the video , I unplugged the appliance and defrosted the freezer . Then removed the shelves and back from the freezer. Located and removed the old parts and installed the new ones which took about 20 minutes. Reassembled the appliance, plugged it in and it was cold within a few hours. Thanks for all the help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alcides from WINNETKA, CA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Freezer was not defrosting. Ice accumulated inside of the back of freezer.
Disconnected the refrigerator for a few hours. On back of frezer compartment unscrew 4 screw to get access to Old defrost thermostat (D. T.). I cut the two wires with pliyers atached to D. T. Peel them about one inch both the old and new D. T. With plyier. Color coded put them together. I used those electrical cap wires to attach them toguether an electrical tape around it to prevent any moisture. Now working like new. Expend approximately $25. And 20 minutes of my time. (I was being charged for the repair. $250.) Now is working like new. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from KNOXVILLE, TN
- Parts Used:
- WR60X30922
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice built up around evaporator fan blades and blades chipped and broke. Refrigerator was making loud vibrating noises.
Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from RCH PALOS VRD, CA
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My shelf inserter broke into pieces.
It was very easy to install and fit right into the shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marty from CONCORD, CA
- Parts Used:
- WR32X26198
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drawer was cracked
Got a replacement drawer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTH PALM BEACH, FL
- Parts Used:
- WR24X10155
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
door gaskets developed mold which could not be removed
out with the old
in with the new
in with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Silvia from KANSAS CITY, MO
- Parts Used:
- WR71X10761
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Broken shelf insert
It was a bit hard to pop it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from HAZEL GREEN, AL
- Parts Used:
- WR49X10091
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refrigerator made EVERYTHING Frozen; Water line was frozen; Ice machine stopped working
This part worked marvelously. I followed a YouTube video to completion. Essentially, I removed the water filter cover by squeezing the tabs on the side. Then, I removed the housing for the light based on the tabs placement. I unscrewed the lighting fixture, unplugged and set aside. After that, I removed the bottom part of the damper assembly (that's not included but virtually attached to the damper) by pulling on its tabs' placements. Then, I pulled off the damper assembly, unplugged the cords and added the new assembly WITH the inclusion of the damper gasket assembly that doesn't seem to have been a part of the old assembly. Rescrewed and reattached everything and now the fridge is as good as new!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from TUCSON, AZ
- Parts Used:
- WR14X10059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
replace seal on crisper drawer
spent 10 minutes trying to clip in the seal without any success. I emptied the crisper drawer and removed it flipped it over clipped the seal. replaced the drawer. Secret is to remove the drawer from the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bradenton, FL
- Parts Used:
- WR50X10068
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer was running warm
You guys ought to win some sort of website Emmy. I found your site as I was searching for a new motherboard, thinking this was the cause of the temperature control problem. I took the time to go through the little diagnostic process you offer and I discovered that the much less expensive defrost thermostat was more often the root cause of the problem ($8 vs $160 for the new motherboard). The part arrived within 3 days and the installation video was enormously helpful. Removal of the rear panel was more difficult than suggested on the video. I'd suggest removing the freezer light fixture before trying to remove the panel as it is nearly impossible to bend the metal panel around the light bulb bases. Anyway, the whole job cost me about $16 for parts and delivery and the fridge is running fine. The combination of the diagnostic tool and the installation video were fantastic...far beyond expectations.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from SHONGALOO, LA
- Parts Used:
- WR49X10091
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator side was freezing all the fresh vegetables in all three of the crispers...even the milk and all drinks were freezing..
Went online and read all the problem an found it could be my Air Inlet Kit...did not know it had one ..was online and ordered it...came in couple days..
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
to replace the damper I just remove the light at the top of the frige and the cover around it .I also removed the filter and filter cover..then the damper assembly only has 2 screws .I removed top three glass trays for more room...was a little easier than I was expecting..just about 30 minutes to hour ...(1) unplug Ref and last (plug it back in). Thanks ...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!