RG2300NGPCBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- earl from mount pleasant, IA
- Parts Used:
- IM6D
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
stopped making ice
five quarter inch screws and to wire plugs. took longer to remove food above and below it than the repairs. very good instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Plainfield, IL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispensing Door would not close
Not only was your parts selection very easy to understand,
The Video shows exactly how to install that part.
This was So Easy to repair. I thought I would have to take
the door apart from the inside but the repair was completed
with the door closed and took about 10 to 15 min. to complete.
The Video shows exactly how to install that part.
This was So Easy to repair. I thought I would have to take
the door apart from the inside but the repair was completed
with the door closed and took about 10 to 15 min. to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Montgomery, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispenser door would not close after use
I followed the directional video on "PartSelect" website. The video was very easy to follow and showed exactly how to easily replace the dispenser door solenoid assembly. I knew it was the solonoid assembly because the I could see the plunger that controls the opening/closing motion of the dispenser door sticking inside the old solenoid. The "PartSelect" website is very user friendly and very easy to use. The part ordered, delivered by standard delivery, arrived the day after it was ordered. I only wish all repairs could be as straight forward and easy as this one, thanks to "PartSelect" and some limited mechanical/electrical knowledge on my part. This was absolutely a "do it yourself" repair at a very significant savings over using an appliance repair service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from north port, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice flapper would not close
Removed front display and solenoid 3 screws and replace. Clean and install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clyde from San Antonio, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper in door for ice dispenser would not close.
I repaired IAW the PartSelect video. Very easy. One thing that should be mentioned in the troubleshooting process, is to check the retention spring on the flapper. That spring could come off and also cause the flapper not to close.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donnie from Conover, NC
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flap in shut where Ice comes from Icemaker to outside of door would not open causing ice cubes to build up so when you opened the door they fell all over the floor.
Simple fix with information furnished online with the Dispenser Door Solenoid Assembly. Unplug fridge, remove selection panel by pulling out gently at the bottom until it releases then unplug the 3 connectors, remove next panel by unscrewing the 4 corner screws, then remove the solenoid by loosening the top screw and removing the two on the bottom, wipe all clean and reassemble in reverse with new solenoid hanging piston over ice door flapper lever first then sliding it into solenoid as you move it into position. Easy fix....$35 hopefully extended the life of a faithful older fridge for a few more years since it work/looks new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Manassas, VA
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper on ice dispenser wouldn't close after dispensing ice.
When I clicked on the part to see it's description the pop up window included a youtube video on how to install the part. The video was right on the mark. Very easy installation. Phillips screwdriver was the only tool needed. Repair performed in less than 15 minutes. I have used this site before and it has been extremely helpful in saving me money by doing the repairs myself instead of paying an arm and a leg for a repairman to do it.
Was this instruction helpful to you?
Thank you for voting!