GSE20IBTAFBB General Electric Refrigerator - Instructions

I called a repair shop and they said the control bd. was bad. They replaced it and about 2 weeks later it happened again. They came out again and replaced the bd. under warranty. About a week later it happened again. This seemed like too much of a coincidence, so I looked around on the internet and found your site. The video showed how to replace the freezer safety thermostat which I ordered on Sunday and received on Tuesday. By then the coils were iced up again. I completed the repair in about half an hour. So far the old GE is working like new. Thanks for the help. I just wish I hadn't spent over $400 for incompetent repair people in the first place. Thanks again, you guys are great! By the way the part only cost about $17 including shipping.

I went on Parts Select and typed in the problem, and they gave me the parts that might be the problem. So, I ordered the two parts, and put them in. Was really easy, as there are videos on parts select to help you remove the part and put the new one in. So simple. My freezer is working right now, so time will tell.

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

Followed the video instructions with the help of a young man who worked on trailer hitches before and knew how to splice wires. Beware of splicing the wrong fan motor back into the assembly. . . . That happened here and we had to start the splicing all over again with the correct fan motor.

Replaced the Defrost Thermostat and the Defrost Heater.

Removed back panel,removed ice maker.And you can see the two wires colors are a snap to identify cut the two wires spliced the new one in done deal!

Emptied Freezer (to get access to panel covering condensor coils and Defrost Thermostat). Pulled off cover panesl. Had to wait for ice to clear from condensor. Replaced Defrost Thermostat (5 min job), replaced panels and was back in business.

Based on instruction I replaced the defrost thermostat and the temperature sensor. There was no improvement. The defrost thermostat was supplied with orange and red wires. the original wires were orange and pink. I connected the 2 orange wires and the pink to the red. So I don't really know if that is the problem or not. currently I don't know what to do next anyone got an ideas? It has dual evaporation.

According to PartSelect website, the probably cause was Temperature Sensor or Defrost Thermostat. I watched the replacement videos. . .. very nice and seemed easy. Ordered the parts and got within 3 days (nice!). I followed the procedure on the video for disassembly, I used a hair dryer to melt the ice buildup on coils and then cut the old Sensor and Thermostat out of the wire harness and, instead of using crimper to seal my new splices, I soldered them instead. I used shrink wrap sleeves, then wrapped in electrical tape for permanent insulation. My Fridge now functions like new again.Thanks Partselect! You are the best!

first unplug unit then pulled the inside back freezer cover off piled towels around and defrosted the the unit thoroughly. located the defroster unit tested for continuity was good so i replaced the temp sensors they were just nip off the old one and splice in the new one. also replace the defroster thermostat was the same nip and splice. *the parts shop did not find the model #i have but knowing those parts are interchangeable with all G-E models i ordered the parts

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

Part select was great. I entered the model number and was able to locate a list of problems associated with my refrigerator. I was able to view a repair video, courtesy of part select. I followed the instructions and the repair was simple. The hard part was trying to remember how everything went back together. I unplugged the unit and removed the freezer racks. I then unscrewed the back panel within the unit. I then placed an old towel inside the unit and used a hair dryer to melt the ice build up inside. I also removed the light bulb and then removed ice maker. I then located the old defrost thermostat and replaced it as demonstrated in the video. I then located temp sensor and replaced it. It took longer trying to secure the rear panels than the actual repair. My mistake was I had secured the ice maker unit before securing the fan panel. I would secure the large panel first, then followed by the light bulb/fan panel. The ice maker should go in last. It has been 8 days since the repair and it still working! The total cost was $27.

I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.

Parts were perfect. Shipment great. It took a bit of time to get back to the Evaporator fan, so i basically had to take the entire freezer apart. Not a problem. The one issue i ran into was my unit had 2 white wires which connected to a silver bullet thing, that were not included in the wiring harness. Maybe I could have ordered that part (thinking out loud) I had to cut the old one apart, and adapt them into the new one, which had 2 holes to spare for this purpose. I guess i could have spliced every wire, but didn't. The freezer now SOUNDS LIKE A FREEZER. Thanks,

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.