ZIR301NBRAII General Electric Refrigerator - Instructions

turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.

PartSelect helped me identify the part, got it in only a few days and I followed the easy to follow video featuring Steve. Awesome!

1. Turned off water near hot water tank 2. Removed back (small section) of the refrigerator, only 7-8 screws. 3. Disconnected the old water hose (comes out easily. 4. Reconnected new water valve 5. Turned on water @ hot water tank 6. Replaced back of refrigerator. All done! I have never done anything like this, and I had no instructions, very easy to figure out. The part cost $48 here.

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

I shut the water supply and took off the rear panel.
One screw released the valve. Pulled off water lines(3) and electrical connectors and installed all on new valve. Screwed the valve and the panel back and turned on the water supply. Prior instructions on website helped. Part came in two days. This part should have never failed. Looks like the housing is two parts glued together. Glue failed after 7 years. G.E. should cover this. My warranty expired after 5 years. M.K. Boca Raton,Fl.

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

Shut off water supply and unplugges refrigerator. Took of bottom panel on back of refrigerator. Discontected power plug and water lines from old water valve, removed water valve. Put in new water valve and reconnected water lines and power plug. Plugged refrigerator back in, turned on water supply and checked for leaks. Put cover back on. (It's also a good opportunity to clean out the dust and dirt under the fridge and around the motor and condensor)

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.

After gaining access to the back of the refrigerator. I shut off the water valve and pulled the electrical power plug. I removed 6 screws from the access panel. I then removed 1 screw holding the water valve. I disconnected the electrical connectors. Disconnected the water inlet tubing with an adjustable wrench. I removed the water to the door and water to the ice maker by pushing in on the collar which released the tubing. I discarded the old valve and installed it in reverse order. Did not fix the problem. My next guess is the control module.

very simple repair.....push two hoses into compression fittings on the bottom, plug two wire harnesses into the back, and put a screw into the front to attach to the refridgerator frame. After that, just turn water back on and plug it in. Ran great.

Part also came in quicker than expected......which was a definate plus.

It was very simple. Pull the fridge back (unplug and turn off water), remove the cardboard backing and disconnect/unhook the current water valve and reverse the process to connect the new.

per the video - took off panel, remove the existing part, and replaced.