JVM1630SPC General Electric Refrigerator - Instructions

Turn off the water.
Unplug the refrigerator
Take the back off of the refrigerator
use socket wrenchs to undo and take off the water valve in the lower left corner of refrigerator.
Pull out and disconnect electrical connections
Pull out the 2 water tubes one for ice and 1 for water-white is water and black is ice.
install the new valve and connect the water and ice back in the new unit
connect the two power cords and reattach unit to the frame Turn water on and check for leaks.
If no leaks put back on refrigerator and plug in.
Wait 30 min to an hour for water to begin to flow back into the unit.

I turned water off at valve and unplugged refrigerator. I removed screws to remove cardboard cover at bottom. I removed screw holding duel inlet water valve bracket and pulled out valve. Then it's just a matter of exchanging electrical connections and water lines. The electrical connections unplug and plug in-red to red and blue to blue. The water lines are two different sizes so they can't be mixed up. Then reattach bracket and cardboard cover. Turn water back on and plug back in.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

Background: My refrigerator was part of the class action law suit back in 2006. As a result both doors, the auger in the ice maker and a heating element in the freezer were all replaced.

Problem this time: Water was not dispensing.

Solution: Replaced the double outlet water valve in the back lower left portion of the refergerator. Water was coming into it from the water filter hose, but not coming out of it when the water dispenser in the front was engaged.

Further, I found that the coils in the back of the freezer were iced up and I therefore defrosted them with a heater. Thus, the original problem encountered with the law suit, did not get fixed by simply replacing the doors. That problem is still there. I think the defroster/heating element in the freezer is again not working.

However, I do now have water flowing again and the installation was, as others have described, very easy. Thanks for the online help.

Moved refrigerator out from wall, unplugged from electric, removed plate at bottom back with 1/4 nut driver, turned incoming water valve off, disconnected water line from water valve on refrigerator, removed mounting screw, remove water lines from valve and electrical plugs, set old valve aside and replace with new valve, reconnecting water lines and electrical plugs then remount bracket, reconnect water line from source, open water valve and check for leaks, replugged refrigerator and depressed the door button to check to see if working. It worked and there was not any leaks. Replaced back plate and placed refrigerator against wall. Job completed.

Moved refrigerator forward, this allowed me to work on the back panel. Unplugged the refrigerator power cord. Released all 6 screws, removed panel then release an additional screw that was holding the water valve and the two (red & blue) connectors. Then installed the new part in reverse steps. Plug the unit and job well done. I had purchase the water filter already after several minutes push for water from the dispensing front part of the refrigerator and good to go, later in the evening we notice the ice maker working fine and producing ice. Thank you parts select.

Shut off power to the appliance. Remove the 8 to 10 1/4in screws holding the main control board cover in place and remove the cover. Use a small screwdriver or pick to gently press in the latch on the 4 plastic clips that hold the board in place. One at a time remove and reinstall on the new board the electrical connectors, gently pull or the electrical connectors by the the plug do not pull the wires. Reinstall board onto the 4 clips and tuck wires so they will not get pinched. Reinstall main board cover and power the refrigerator.

Originally I thought that the Start switch was the issue, and ordered one. After taking the machine apart and running some tests, the issue was clearly not this switch, but a different switch that cuts power when the belt tension is no longer being applied to the idler pulley spring. I fixed this by bypassing this switch, which in my opinion, is error prone and serves no purpose. The switch can be accessed by removing the control panel, then top cover, then front cover, then drum. The bogus switch is screwed to the bottom left, near the motor. The idler pulley spring rests against it. Just disconnect the switch wires, then clip, strip and crimp then together to bypass the switch, and voila! Now if the belt breaks or comes off the pulley, the motor will continue to run, but you wont hear the wet clothes flopping around, so that will be the indication that you have a belt problem. Hope that helps!

You have to remove the shelves and drawer's along with the drawer mount. there is a wiring harness you need to unclip to remove the crisper electrical panel

There are six nuts to remove the lower panel at the back of the compartment where the lower drawer normally is. no need to completely remove the panel, you only need to get wiggle room to remove the fan at the base of the center panel.

There is a small triangular cover used to conceal the fan wiring harness on the right side of the center panel that you can use the putty knife to slip in on the center panel side to unclip and remove

Use the putty knife and slide it down both sides of the center panel that runs vertically to unclip it - at the base of this panel is where you'll find the condenser fan, you should be able to wiggle it out - there is a built in clip on the lower right side of the center panel that you can slip the wiring harness out of - for me this was the hardest part of the replacement as it was just awkward.

After it's removed slip in the new fan and seal and reassemble. I think the whole operation took maybe a half hour - 40 minutes. It's pretty easy all said and done.

I asked two strong male neighbors to do the work and told them how to do it. Follow the simple directions on the box. You can Google it, but it will tell you the same directions.

followed install on line

-Pulled refrigerator out to access back.
-Removed compressed paperboard cover.
-Found compressor running by the feel.
-Removed metal cover to control board.
-Found ~5V coming from control board to inverter (variable frequency drive) board assembly attached to compressor.
-Found ~120 going to inverter board.
-Removed inverter board assembly from compressor.
-Found equal resistance (~7 ohms for mine) at all three contacts of inverter (DC) compressor.
-Ordered inverter assembly, plus one extra and control board for possible future use so not to loose all my food again; I might order a compressor so I have it before price goes up.
-Installed inverter when arrived.
-Used air compressor to blow out accumulated dust on condenser coil.
-Closed up and cleaned up (C^2).
-Fridge cooled and back to proper temperature the next day.

Using a screwdriver, removed the cover, pulled out the bad bulb, and easily put in the new one.

I simply took the back panel behind the timer unplugged the old part and when the new part came in I hooked it back up in less than 5 minutes. I did mark each wire to match order I took them out.

Took out interlock switch (two leads) and replaced with new one. As simple as that.