GNR22DGEBRWW General Electric Refrigerator - Instructions

Used this site to find probable problem - stripped teeth on knob - and how to get old knob off using needle nosed pliers to remove clip. So also ordered replacement knob from this site - got it in one day! Took about 2 minutes to put replacement knob on. Most of repair time was figuring out what the problem was.

This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

Removed knob by using screwdriver to pry out plastic retainer. Put new knob on the timer. Took about 5 minutes. The problem was caused by the wearing out of the teeth on the knob.

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

I removed the old knob (very easy, used a flathead screwdriver to remove the clip and off it came). Put the new knob and clip on and voila!!!! It worked. My local appliance people wanted over $100.00 for the same part. Definately using Parts Select if issues arise in the future.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.

Super easy repair, just removed the old latch and replaced it with the new one.