GNR22DGEBRWW General Electric Refrigerator - Instructions

The parts were here in 3 days and the repair went very quickly .Quality item would do business again.

replaced Tub dampeners Straps.

After reading how others have done this and how easy it was, I decided to give it a try. And, sure enough, it was really easy. However, one concern I had was on lifting the old agitator off from the axle using both hands. I didn't want to have the agitator come crashing into my face as I pulled up. So I put a pillow on top of the agitator.

Unplugged the dishwasher and turned off the water. In order to pull the dishwasher out I had to remove disconnect the waterline. Opened the dishwasher door to remove the screws attached under the counter holding the dishwasher in place. Once removed I pulled the dishwasher out of the under counter pocket far enough that I could access the rear connections to the heating element. Carefully disconnected the wires connected to the heating element and then loosened the large nuts securing the heating element. Once the nuts were removed I disengaged the element from the holders and removed it from the dishwasher. Installed the new element in place engaging it into the holders inside the dishwasher. Then moved back to the rear of the dishwasher installing the nuts that were removed earlier on the new element and reconnected the cables.

I ordered my new heating element prior to checking the continuity of the old one. I checked the continuity of the old one once it was removed and it was ok, not great but still acceptable so I knew the new element wasn't going to fix the issue, but installed it anyways. My issue was actually the float switch, so if you want to be sure of your issue, remove the current heating element from your dishwasher and check the continuity before ordering if you want to save some money.

Parts Select has excellent video instruction. they are way better than I could describe. the repair went smoothly. the heating element wasn't the issue. and it's may not be yours either. I found that the flood switch was the problem part number PS8690623. It's located under the filter screen in the bottom Yes that long grey plastic thing under the screen. It's held in by two 1/4 inch screws. Use a wet dry vacuum or towels to dry up the water in the sump. ABOVE ALL don't drop the screws. You'll be taking the pump apart if you do. Gently lift out the flood switch. There will be wires plugged into the base. With a flat screwdriver gently pop off the white plug from the green base. The plug only goes on one way reassemble in reverse order.

1. Remove lower dishwasher rack.
2. Remove flat course filter screen in bottom of dishwasher by unscrewing the 2 hand screws at the rear of the screen. Remove the round fine filter (at the front of the course screen) by rotating counter-clockwise by hand.
3. Remove both the fine and course screens exposing the 4 inch tall, skinny, round float valve. DO NOT rotate the float switch--remove the float switch by pulling it straight up.
4. Remove the electrical plug on the bottom of the float switch.
5. Install new float switch taking care to remove the old O-ring and ensuring the new O-ring is properly located at the bottom of the new float switch.
6. Follow instructions in reverse to complete the reinstallation.

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.

The grooves on the bottom of the control knob were worn away. I just pushed the timer knob clip off of the underside of the knob, removed it from the washer and put the new knob on and put the clip back on. It was a piece of cake!

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

took the needle nose pliers and removed the timer knob clip from the back of the control knob. Removed the control knob and the dial with compression ring. Installed the new dial compression ring and pushed the control knob on. Note: the new control knob comes with the clip allready on the back of the control knob. Took me about 3 minutes to replace.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.