TFT22JADAAA General Electric Refrigerator - Instructions

I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!

Since the original part was a single element we had trouble locating the part we were replacing since it was replaced with a dual heater. Once located the repair went pretty well. We followed one of these wonderful postings that helped work through the difficulty.

1. Unplugged refrigerator from wall power socket.
2. Removed the 2 1/4'' screws and removed the back panel in the freezer section
3. Defrosted all of the ice off the coils and heater using a blower dryer which took about 10 minutes and lots of towels.
4. I replaced the defrost heater by following the provided instructions. I had a single element defroster which was replaced by a double element defroster. The instructions provided showed how to modify the wiring and were simple enough to follow.
5. Installed back panel and plugged in the refrigerator.

I checked on the defroster 1 week later and was pleased to see no ice on the coil. Problem solved.

The repair stories for this part are helpfull. The only problem I came accross was figuring out which part I needed to order. The parts diagram only showed one part labled 230, but when I used the drop down box to order the part there were 2 parts labled 230 for 2 diffrent prices. I called ge customer care and found out the less expencive part listed as 230 does not come with the wires etc. . The more expensive piece has the wire harness and every thing needed. I went with the more expensive part and it was a snap to install. . . .

Disconnect the broken one and install the new one

Take off the panel in the freezer side to expose the heater, defrost all the ice. Remove the screws that hold the heater in place and remove the wires from each end. Plug in the new unit and replace screws. Replace screws in the freezer panel, to complete the instulation. It will take the most time to defrost the ice, and clean up the water. To help defroct I used my wifes hair dryer. (She did not know it)

Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done

I hung the new shield on the two inside pegs that were already there.

Cake walk repair.

Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, tighten and install cover. tool me 6 minutes.

After unplugging refrigerator and allowing freezer section to defrost completely I removed the lght cover in the freezer section and the green ground wire that is clipped to the panel. I was then able to get to the 2 screws needed to remove and pull out the back panel. I removed the failed heater from the bottom by disconnecting the blue and pink wires from the heater. I was replacing a single heater with a double heater so I needed to dress the blue wire down the right side of the evaporator. I positioned the double heater with the yellow jumper wire on the left and continued to connect the blue and pink wires into either socket on the heater. Be sure not to touch the bulbs with your fingers as they could be damaged by the oils on your fingers. Secure the heater by re-inserting the 2 mounting screws. Re-attach the green ground wire with clip to the back panel before you screw the panel back on. Restart the refrigerator and you are done. This was so easy and I saved over $120.00 doing it myself!!!!

remove screws in back panel and remove , defrost coils wit hair dryer,remove two screws that hold defrost heater unplug wire's.plug in new heater put screws back in ,put panel and screws in ...done

Removed the internal cover and used a hair drier to defrost the evaporator. Unpluged the conectorto the harnes. Placed new part in and pluged it in, replaced cover and tested.

Super simple! Hardest part of the entire process was identifying which part I needed to order. Once I received the part (which shipped promptly and was at my front door within 2 days), all it took was 5 mins and a screwdriver and I was back to having a usable snack drawer!

Not really sure of the age of this fridge, as we bought the house 2.5 yrs ago.

I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and lifted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install.
Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"...
All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it).
Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother?
Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that.
Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves.
Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.

took the panel out of the back of the freezer removed heating element put 2 screws back in the heating element for 2 screws back in the back of the freezer and the shelves