TFX25ZPBAWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scot from Fort Collins, CO
- Parts Used:
- WR17X4358
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Tubing from vavle to reservoir had been degraded by compressor heat and had cracked, leaking water when door water dispenser was used.
- Disconnect the valve assembly and remove electrical connection to water dispenser valve to prevent accidental water discharge
- Disconnect tubing from valve assembly, remove and keep compression nut.
-Disconnect tubing from junction to door tube remove and keep compression nut
-Remove screws used to mount reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.
- Note that one of the tubes on the new reservoir is 2' too short.
- Go to hardware store to purchase 5/16" universal tubing compression junction.
- Install reservoir and feed tubing through holes in main refrigerator compartment.
- Route tubing through woven tubing protectors and clips.
- Trim tubing to length and install in valve using old compression nut.
- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.
- Connect end of tubing to existing junction using old compression nut.
- Re-connect wires to valve solonoid and test for leaks.
- Re-install valve assembly to refrigerator frame.
- Disconnect tubing from valve assembly, remove and keep compression nut.
-Disconnect tubing from junction to door tube remove and keep compression nut
-Remove screws used to mount reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.
- Note that one of the tubes on the new reservoir is 2' too short.
- Go to hardware store to purchase 5/16" universal tubing compression junction.
- Install reservoir and feed tubing through holes in main refrigerator compartment.
- Route tubing through woven tubing protectors and clips.
- Trim tubing to length and install in valve using old compression nut.
- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.
- Connect end of tubing to existing junction using old compression nut.
- Re-connect wires to valve solonoid and test for leaks.
- Re-install valve assembly to refrigerator frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from CONROE, TX
- Parts Used:
- WR17X4312, WR17X10275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rusted Auger and Broken Ice Bin Door
After bagging the ice in the old bin and rinsing out the new bin, I removed 4 screws that held the old ice bin facing/door frame to the old ice bin and the facing came right off. Then I just screwed the facing on the new ice bin, popped the new door into place, and put the new ice bin back into the freezer. Although web descriptions for the parts I ordered referenced GE and other appliance brands and not Kenmore at all, the search engine led me to these parts and everything fit perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from South Lake Tahoe, CA
- Parts Used:
- WR17X4358
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Dispenser Water Reservoir failed seem
This was a very easy fix. I cut the water lines at the reservoir, coupled the old lines to the new lines with two plastic barbed fittings used for outdoor drip irrigation. All I had to do was pull the old lines out and the new lines followed. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROY L from TIGRETT, TN
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice bucket was broken
it was really easy now it works like it did when it was brand new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from MODESTO, CA
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Water line was leaking
The internal water line was leaking. I could not find any repair parts for my refrigerator but the GE 5/16 water line was the same size. I purchased 6' of tubing and two unions. Make sure the clean and square. If possible, make the cuts in a spot where you can use the pliers and wrench to tighten the union. I cut approximately 2' out of the existing line and replaced it with the same length of new line using the 2 unions, one on each end. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Indian Trail, NC
- Parts Used:
- WR02X11330, WR17X2891
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
5/16" tubing to chilled water dispenser cracked
Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Mount Airy, NC
- Parts Used:
- WR17X2059
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
would not crush ice
you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from FREEHOLD, NJ
- Parts Used:
- WR17X4341
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old auger was rusting
removed old auger; replaced it with a stainless steel auger
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from martinez, CA
- Parts Used:
- WR17X4341
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The existing auger was rusty and made the ice taste bad.
Removed the screws holding the faceplate. Then couldn't change out the auger so needed to remove all of the other screws in the unit and fully disassemble the icemaker unit. Should have marked the parts as I took them apart as I needed to find a parts diagram on-line to reassemble. Not sure that I put them back together right as the unit will not dispense whole ice cubes as it did previously.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rockford, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
heavy frost buildup in ice dispenser chute and door
After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from ALBUQUERQUE, NM
- Parts Used:
- WR17X3489
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
LIGHT SHEILD BROKE.
SNAPPED THE NEW SHIELD IN PLACE. DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angel from Chandler, AZ
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice was discolored due to rust on auger
Removed the old assembly from the refrigerator. Used a screwdriver to remove the four screws attaching the old assembly to the plastic front plates. Opened the box holding the new part (which had arrived very promptly at our doorstep), removed it and attached it very easily to the plastic front plates using the same four screws. Placed the new assembly in the refrigerator and started making new ice. It was EASY!! We had read what others had said about this repair and knew it would be something we could do. Your website is very user friendly and helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Cumming, GA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Light Shield
Removed the Ice Maker container. Removed the one screw that held the remnant of the old light shield. Placed the new light shield in place and installed the screw. 5 Minutes from start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Danbury, TX
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker Auger and ice was rusty.
Pull out the old, dump the nasty ice. Remove 4 screws attached to the front cover. throw in trash, replace with new auger assembly, with 4 screws. Put it back in ice maker and let it make ice. Easy, cheap and never left the house to searc for the right part, found it on the front porch.
Was this instruction helpful to you?
Thank you for voting!