GTS22JBPDRCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Hudson, OH
- Parts Used:
- WR60X10220, WR60X10207, WR02X10100, WR02X10098
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
squealing noise and refrigerator was feeling warm
Without the video, I would have been lost. I pulled the entire bracket out of the refrigerator, but could not insert the tab and adjust the bracket back in place, so I removed the bracket and motor, inserted the main frame bracket then re-installed the motor, fan , grommets, bracket. It's working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from York, PA
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer not cold, Frig cold enough, runs all the time, Hot to touch in spots.
My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from vernon, AL
- Parts Used:
- WR50X10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
fridge stoped cooling
unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andenet from Haymarket, VA
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Fan and housing cannot be removed together.
On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Lyndhurst, NJ
- Parts Used:
- WR02X12149, WR02X12008, WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Unusual noise from freezer.
Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from Montebello, CA
- Parts Used:
- WR72X10073
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide pan lh
pull out the slide pan lh and replace for the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Altoona, IA
- Parts Used:
- WR60X10220, WR07X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
the fan motor wouldn't run and the refrigerator wouldn't cycle.
Unplugged refrigerator and removed rear cover. Removed the two attaching cap screws from the mounting bracket. Removed fan blade by sliding it off the shaft, disconnected wiring plug and removed the motor. Removed the rubber grommets from the old motor and installed on the new unit. Set the new unit in place and reinstall the fan blade, mounting bracket and screw into place. Reconnect the wiring harness. To replace the relay, simply remove the wire clip from the relay cover, slide the relay off the connecting pins on the compressor and disconnect the wires. Slide the new relay into place, reconnect the wires and replace the cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELIZABETH from BOULDER, CO
- Parts Used:
- WR72X10073, WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
shelf brackets holding meat/cheese drawer cracked.
I unscrewed two brackets on each side (Had to buy the correct little screw driver) and screwed in the new ones.Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JULIA from WARWICK, NY
- Parts Used:
- WR72X10073, WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Left Slide Pan Broke Off, Needed To Replace It
Remove entire shelf from refrigerator and removed broke, set the replacement part in place, screwed it in and it worked perfectly, done infive minutes. Took me longer to take out the self that to do the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jamestown, ND
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide track on right side of chill tray, where it was held together, on the metal frame, the screw cracked the plastic.
Went to Sears, where I bought the Fridge, they could not locate the part I needed, so I went on line, and found partselect.com, entered the proper information, found the part I needed fast, ordered the part, received it in two days time, I already had the old part off, so it took less than ten minutes to replace it with the new part, works great, the people at partselect.com were great, an if needed, I will gladly order from them again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TREVOR from KENT, WA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Burke, VA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The plastic piece that holds the screw in on the pan of the refrigerator had broken
I took the pan out, replaced the bar with the new part - slide pan RH - and I was back in business. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Brooklyn, NY
- Parts Used:
- WR72X10072
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Guide rail cracked
My snack tray guide rail cracked and this was the easiest repair I've ever made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Johnson city, TX
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dripping from condensation. Noticed fan wasn't running
Pull the old off ..put new one on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grace from Arlington, TX
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and fridge parts had stopped cooling
I followed the instructions on your YouTube video exactly and it was a snap. By far the hardest part of the repair was to fit the back tab of the fan assembly in the tight slot on the way out. The result was immediate and like having a new refrigerator. I'm a 68-yo retired woman but thanks to you I now feel empowered -- will tackle next appliance repair with confidence. Thank you.
Was this instruction helpful to you?
Thank you for voting!