GTS22JBPDRCC General Electric Refrigerator - Instructions

Removed the fan blade then removed the motor. Replaced motora nd Installed fun blade.

Laying on my side.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

I followed the video for my model refrigerator on parts select. My hint: when returning the back panel of the freezer, it's slightly adjustable left and right to avoid grazing the fan.

Attempted it on my own with the aid of the video on your site, but could not remove the fan shroud due to additional copper lines that prevented me from getting it out.
Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out.
All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan.
The repair guy's comment: "I've seen that before with some of the aftermarket fans."
Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Gaskets designed to just press a flange into channel around doors. I tried everything..I pre-heated gaskets ; I put dish soap around flange; I used (carefully) a heat gun as I pressed gasket in. Really very difficult to get the gasket to seat fully. I don't know if there is a tool to help you do this, but you need strong fingers/thumbs and endurance. Once seated, you will need to heat the gasket to get it to fully seal against the fridge. Just lightly heat along the gasket with the doors closed and press open the fold with your fingers. I let the doors stay closed over night. Works great now, but I probably will call a repairman the next time. I miss the old gaskets with a zillion screws..PITA, but easier.

I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one

Easy

Nothing much. It needed the snack pan, which it has never had.
The door was the main issue. My young son would hang on the door. We started having problems with it not closing. Then on day it snapped off. We repaired the screw but found the hole was stripped out. We moved the door to the other side. When the door fell off it broke the upper door shelf. This was a quick slide in repair that did not require any tools.

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

pull out the slide pan lh and replace for the part

I removed cover above the light from the back of the freezer. I removed the fan and clipped the wire leads, after disconnecting the breaker to the fridge. I connected the wires with wire "union" from Radio Shack. Could have used wire nuts. I put the breaker on to check that it was running, then put the cover back on. However, to fix the build up of ice on the coils in the back of the freezer, I also replaced the thermisor and the heater coil after defrosting the coils with a hair dryer. Both were easy repairs and the fridge works fine.

Pull the old off ..put new one on