TBX22RPRRWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TERESA from COALMONT, TN
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Was Not Making Ice Or Getting Water
Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tara from cumming, GA
- Parts Used:
- WR24X446
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
needed to replace the gasket because it had become brittle
My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie B from Hollister, NC
- Parts Used:
- WR23X318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the ice dispenser quit working
I opened the freezer door and removed the access panel, then with a phillip screwdriver,I removed 1 scew and used a pair of pliers to pull the wires off.I then reversed the prosess.EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from FARGO, ND
- Parts Used:
- WR24X445
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
had moved into new house and discovered freezer door gasket incompletely sealing tried using home warranty service but decided trying rather than 100$ service fee. ordered gasket and watched several u-tube videos.
Placed new gasket into dryer,( recommended by 2 u tubes) high heat for about 10 minutes and was a snap getting softened gasket into little tiny slot actual placement was done twice as there was a twist in the seal i missed the first time so did do twice but was so easy this way was almost sad thinking it would have been 100$ deductible having someone do it and who knows what normal cost would have been......thanks u tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from KANSAS CITY, KS
- Parts Used:
- WR60X10262
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Bin of cubes was frozen over and I thought I had burned out the auger motor
My friend easily installed the new motor but that wasn’t the problem it ended up being the control panel board on the fridge freezer door that is the problem. No one has that part #WR55X0058
That I need and I can’t find it on the internet they say because my fridge is almost 30 years old. I’ll keep searching. My fridge still works perfectly and makes cubes. They just won’t dispense. It’s my spare fridge and I’m not ready to get rid of it.
That I need and I can’t find it on the internet they say because my fridge is almost 30 years old. I’ll keep searching. My fridge still works perfectly and makes cubes. They just won’t dispense. It’s my spare fridge and I’m not ready to get rid of it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SCARBOROUGH, ME
- Parts Used:
- WR2X4550
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was leaking and causing the ice to freeze into a block.
People would use the ice maker and just let it grind and eventually the bin and the plastic cup at the end of the auger broke.
I replaced the ice maker and once satisfied it worked and did not leak, I took the bucket/auger mechanism apart and replace both the bucket and the ice cup.
While the Frig is getting old, it has paneling that matches our cabinets so we are trying to get a few more years out of this. This repair is one I should have done 10 years ago! Thanks Parts Select!
I replaced the ice maker and once satisfied it worked and did not leak, I took the bucket/auger mechanism apart and replace both the bucket and the ice cup.
While the Frig is getting old, it has paneling that matches our cabinets so we are trying to get a few more years out of this. This repair is one I should have done 10 years ago! Thanks Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Lewes, DE
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no water to icemaker
removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marj from NEWBURY PARK, CA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light dead even with new bulb
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joy from BELMONT, NH
- Parts Used:
- WR24X446
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
water build up in bottom of refrigerator
Allow 24 hours for new gasket to flatten out from packaging. Gently peel off existing gasket. Clean dirt and mold from mount area.
Mount gasket beginning at a corner. Press gasket into place every inch around perimeter. Done! Water is no longer in bottom of refrigerator and it is running more efficiently (less time running) due to the fact that it can maintain the temperature for longer periods of time.
Mount gasket beginning at a corner. Press gasket into place every inch around perimeter. Done! Water is no longer in bottom of refrigerator and it is running more efficiently (less time running) due to the fact that it can maintain the temperature for longer periods of time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADLEYVILLE, MO
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken light switch
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from EAST JORDAN, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light went out in refrigerator
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from WILLIAMSPORT, PA
- Parts Used:
- WR60X30349
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Evap fan failed, would need restarted by hand when weather warmed up
Repair was super simple. Everything was a direct fit. Hardest part was unloading freezer to access evap motor. My freezer was old making my wire shields very brittle so I cut the shielding and used heat shrink tubing for a neat clean repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bryan, TX
- Parts Used:
- WR24X446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
sweating / leaking water
it was so easy I need to put an ad online to replace gaskets got the right part on time get fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Glendale Heights, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Light would stay on when door closed
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
Was this instruction helpful to you?
Thank you for voting!