TBXA22ZRBRAD General Electric Refrigerator - Instructions

took a little more effort than the video show to remove old module and replace new. Works fine now.

I ordered the part one day and it was in my refrigerator by the next day. No tools required. You guys are incredible. This is the second time I ordered parts from you. You never disappoint!!

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

pluged the wire harness into the new socket from the back and snaped the socket in place.

removed the screws and then replaced the rails. Easy

Tool glass shelf out and attached the drawer slide with the two original star screws. Did not bother with the left side. I ordered both drawer slides even though only one side was broken. I had tried some epoxy first but it didn't want to stick to drawer slide plastic.

I took the drawer and shelf out,unscrewed the old slide, then screwed the ne wone in. Put the shelf back in and then slid the drawere right in!

This was very easy. Just unscrew the broken side pieces and attach the new ones. If the rubber gaskets are still in good shape, gently pull them off and attach them to the new rails. I was very impressed with the service from Partselect.com. I gave them my appliance model number and they helped me find the right part. I ordered on Sunday evening and had the parts in hand by Tuesday. Great service! I will definitely use this company if I need more parts.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

I took out all the stuff on the shelf, and the drawers.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.

Wasn't sure what I would find underneath the old gasket, so I went slowly at first, but once the first side was off, the rest of the gasket came off quickly....and the metal track under it was clean and in good condition. After cleaning the areas where the gasket would seal, my daughter and I each started at a corner and placed the gasket into the track. Entire thing done in less than 10 mins. Piece of cake...only issue was a crease in the outer cushion area....I couldn't seem to smooth it with the warm water bath....it may uncrinkle with time...right now it is leaving a very small space when the door shuts. Saved me the expense of a new unit right now...hoping this takes care of the cooling issue I have with the unit keeping fresh veggies fresh.

Removed the broken rail (2 screws), replaced the new rail (2 screws), reassembled all in about 8 minutes. It was AWESOME!!! I had spent hours trying to repair it and, fortunately, gave up and decided to look online for the part. Didn't even think that the part would still be available. Not only was it available but it arrived in 2 days! Anything that is broken in the future: I am going to your website first! Thank you!!!

Remove bottom glass shelf, lift up -then remove entire drawer slide assembly.Remove plastic decorative front cover(it just snaps off) and unscrew left side drawer slide screws.replace with new part and screw in screws. Replace in bottom of fridge and replace glass shelf.So Easy that an average house wife like myself was able to do it alone.Almost as easy as finding the part needed on partselect.com! Thanks, it was much easier than apple pie.

I removed the gasket starting in one of the corners, until the gasket was completely removed.
I then replaced the gasket with a new one by starting in one of the corners and pressing it on to the track around the door.

I took all of the creases out of the new gasket with hot water as described on the delivery box. I laid the gasket on the floor and let it cool while I took the refrigerator door off, laid it on a table, and removed the old gasket. I started the new gasket into the groove at one corner and pressed it into place by sliding my thumb along the gasket and seating it as I went. It was an extremely simple task which took about 2 minutes. The most time is consumed in removing and replacing the door