GTT15HBMFRCC General Electric Refrigerator - Instructions

Followed the video by Parts select. Very accurate to remove and replace. The only trouble I ran into was getting the clip back onto the fan blade shaft! Have to improvise and use a wirenut to spread it and it went right onto the shaft. Now working perfectly! Thanks for the video and the fast part service shipping...

followed the video provided on internet by Parts Select. Video is very well done. Thanks

Part came in a couple of days, very fast delivery. Read how other people installed. Only drawback was the youtube video was not available. Thanks again!

refrigerator was not cooling. with new fan the refrigerator is working so well I had to turn it down to "1" to get the temerature right.

Watched video repair by Hotpoint , Everything went like clockwork and was a total success. Repair took exactly 25 minutes.

I followed the video instructions and the job was done in no time at all

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

took of the metal plate four screws also the plastic cover two screws. then took the fan off two screws , then took the fan off the motor, remove the metal clip off the tip off fan

emptied the freezer compartment, unfastened the air column panel, then four small bolts to remove the back panel in the freezer, unplugged the motor, unscrewed the motor, installed all in te reverse order and had the compartment refilled and running again in less than a half hour.

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

Basically I followed your video replacement steps and it took me about 20 minutes to replace the fan and foam air duct. The video really made it easy to fix the problem of the refrigerator not cooling properly. Works great now. Thanks for your help it save me between 200/300 bucks to a repair person.. Don

watch the video very good

I had already ordered a replacement evaporator motor from another vendor. I ordered the evaporator fan blade, compression ring and rubber grommets from PartSelect. Apparently this is a pretty common issue with top-freezer refrigerators. Obtaining these parts and possessing the few tools needed saved me at least $100 over having someone else perform the repair. I will further use PartSelect when ordering parts for my other appliances. Thank you.

Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!

unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.