GTT15HBMFRCC General Electric Refrigerator - Instructions

I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

No problem, had the job done in twenty minutes,Thanks John

My wife and I followed the installation video & put the gasket in hot water. We struggled to get it started in the second corner on top. Gasket had cooled down so wasn't wanting to go in the slot. I finally got the bright idea to use a hair dryer to warm the gasket as we pushed it along.
That helped us finish the installation.
Not sure the new gasket is the complete answer to the leakage at the top of the door (forming ice crystals). The MAGNETS ARE WEAK compared to my 1 year old GE top freezer refrigerator!
My newer refrigerator "snaps" shut.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Removed the back of the freezer, 4 screws, and then unscrewed the motor mount with fan and motor attached. Switched fan blades to new motor. Reinstalled motor mounting then back of freezer. I had to go buy the ring opener tool at the auto parts store. $12.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

refrigerator was not cooling. with new fan the refrigerator is working so well I had to turn it down to "1" to get the temerature right.

I followed the video instructions and the job was done in no time at all

emptied the freezer compartment, unfastened the air column panel, then four small bolts to remove the back panel in the freezer, unplugged the motor, unscrewed the motor, installed all in te reverse order and had the compartment refilled and running again in less than a half hour.

took of the metal plate four screws also the plastic cover two screws. then took the fan off two screws , then took the fan off the motor, remove the metal clip off the tip off fan

I watched your Video. Thank you.

First thing I did was un-plug the fan motor located in the freezer compartment and test it for voltage, which it had, telling me the fan motor was shot.I ordered the parts, they arrived in short order and the fan motor was replaced. It took little time and there were no levers, pulleys,servos, gobs of wiring or stacks of gears in a maze of bearings to deal with. Unplug the unit, remove the food rack, ice cube maker(just loosen the 2 screws and lift up)remove the air channel in the center as well as the back panel. Unplug the fan motor and remove the screws securing the motor bracket and lift out. Very simple.