GTL22JCP General Electric Refrigerator - Instructions

Nothing much. It needed the snack pan, which it has never had.
The door was the main issue. My young son would hang on the door. We started having problems with it not closing. Then on day it snapped off. We repaired the screw but found the hole was stripped out. We moved the door to the other side. When the door fell off it broke the upper door shelf. This was a quick slide in repair that did not require any tools.

Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

Part received quickly and was a very good deal!

The broken slide rail mounting was held with 2 screws. I removed the plastic shelf on the top and unscrewed the broken part. I replaced it with the new slide rail part and screwed in the 2 screws. I replaced the slide drawer and the top shelf and the job was done...... very easy! Very satisfied!

Remove the drawer and the shelf glass assembly. using a #2 phillips screwdriver remove the two screws that hold the drawer slide rail. Discard the old slide and place the new slide in position and install the two screws. Be careful not to over-tighten the screws. Place the drawer back on the slide and close it. Next place the front of the glass shelf under the lip on the front of the slide rail and set it in place. Job Complete!

pluged the wire harness into the new socket from the back and snaped the socket in place.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

I just took the broken one and replace it with the new one that I ordered. very easy. Thank you!

Removed the old part using a phillips screw driver, cleaned the area, screwed in the new part, replaced the drawer. It was very easy to do, didn't even have to call my husband.

Piece of cake - just unscrew the screws and put the new piece on, replace the glass top and replace the drawer. No brainer. Don't ever pay someone to do it.

We went for months not knowing where to get the part we needed until my husband found your site on line. The first part we received was wrong, but with the help of your operators, we then received the correct part. It was only a matter of removing two screws, placing the slide and then putting the 2 screws back in. It was a snap.

I thought I'd be nice and surprise my boyfriend by cleaning his frig for him. In doing so I broke the little plastic rail. I felt bad because the frig is not that old. I asked him where the owner's manual was, and he had no idea. Typical male. So I got on line on the GE website and tried to look up the part number, but they didn't have a diagram of the inside of the frig. I went to your website, found the part in minutes, ordered it, and amazingly it came in just two days. It sat on the dining room table waiting for him to fix it for 4 days. I finally got sick of looking at it on the table so that morning while he was still sleeping I grabbed my handy little cordless screwdriver, unscrewed the screws, slipped the new rail in, and screwed it in. It took less than 5 minutes. He got up later in the morning and asked me where I put the rail and glass top. I said "Where it belongs!" He was shocked.

Ordered the part on Monday, it was delivered Thursday morning, and installed in less than 10 minutes. Part Select is awesome, would definetly use again!

the slide had broken so ordered ane one according to model and serial numbers..recieved par in 1 day and put it on in less than 5 minutes

First I removed the glass shelf on top of the drawer. I then removed the drawer and unscrewed the old drawer rail. After this I cleaned everything, screwed in the new drawer rail, reinstalled glass and drawer and I was finished.