TBX18AGC General Electric Refrigerator - Instructions

Detached the old part from the refrigerator and disconnected the low voltage quick connect. Also disconnected the water line to the Ice Maker. Reinstalled the new part in the order it was disconnected and re attached the water line feed to the valve threaded connection. Turned water on and no problems.

I monitored the ice maker after it stopped working and noticed it was not filling with water. I loosened the water feed hose to the single valve outlet and the water feed was fine. However, the single valve outlet never activated to turn on the water feed. I disconnected the waterfeed and electrical connection from the single valve outlet and removed it. Replaced it with the new one, reconnected the water feed valve and electrical connection....allowed the ice maker to cycle and it started filling the ice maker with water right away. The unit is functioning fine now. Thanks to Select parts for filling my parts order fast and accurately. Regards.....E. Tew

Move unit out to access rear. Unplug unit. Shut off water supply. Remove lower cover with phillips screwdriver. Remove valve and both water lines. Install water lines back into new valve and install valve back into position. Turn on water supply and check for leaks. Install cover. Plug unit back into wall. Let icemaker produce some cubes to make sure everything is working correctly before pushing unit back into position. Very easy!

Your online instructions were easy to understand and follow. I replaced the outlet valve which took about 20 min. Then I had to dissasemble and remove icemaker to de-ice inlet tube and back wall of frezzer to defrost cooling fins. All to gether it took me about 1hr / 40 min. Frezzer now works just like new. Thanks for making it affordable and easy. Curt

Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.

removed the inside fridge electrical panel and swapped switches

Hi, My furnace when out when I was away, frozen water lines were repaired, but my ice maker line was turned off, the valve split open. Summer is coming I want ice! I found the right replacement, ordered it, watched the free video, did the repair. It was so easy. And I saved an expensive service call. I am drinking a soda with ice from the ice maker as I type this! Thanks for solving my problem, I will be back next time something needs a part! Bob

easy pry out, disconnect wiring, connect on new switch and press in switch.

I opened the refrigerator door, slid the new crisper tray in and I was "in business! You are awesome! The refrigerator is 31 years old and I gave up trying to find parts in Seattle and decided to check on the internet.Thank you. It was all so easy!

I just put the Ice Bucket under the Ice Maker.Problem solved.

turn off ice maker Shut off supply to fridge unplugged fridge unhooked water supply line unplugged harness plug to valve.

Replacement of the single outlet valve kit went very well. But, water was still not dispensing. I checked if the valve was working by taking the following steps after installing the new valve: unplugging the refrigerator, disconnecting the water line from the underside of the new valve (line to the ice maker), putting a container under the valve to potentially catch water, plugging the refrigerator back in to start the cycle of the ice maker (remember that the cycle will start only if the temperature cold enough). I saw that the valve worked by dispensing water for a short period of time into the container. Taking my chances (with my limited experience), I disassembled the ice maker in the freezer and found that the water line was plugged with ice. So, I really didn't need to replace the valve after all. But, I'm glad I gained some experience.

I first disconnected the plug from the wall outlet. I then turned off the water supply to the back of the refrigerator. I then disconnected the two lines to the water inlet valve and removed the nut that holds the bracket to the refrigerator. I removed the water valve and installed the new one the same way in about 5-10 minutes. It was very easy, but, unfortunely that was not the problem.

First of all, I was very surprised and pleased that I could even locate the replacement part for such a refrigerator I've had for years. The two crisper pan covers arrived the next day (couldn't believe the fast delivery). I proceeded to take the broken crisper covers off and replace them with the two new ones, which fit perfectly. I then slid the crispers into the slots so they could slide in and out. It took me less than five minutes to do. No tools required.

Connected the 2 wires and pushed in the switch until it clicked.