GSS20DBTC General Electric Refrigerator - Instructions

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Simply followed the video -- VERY helpful... BUT: getting the bottom tab to re-insert into the holder after the motor was replaced was VERY difficult...!!! Until I discovered that I could move the refrigerant coil (upon which the tab mounts) just enough that I could get the tab inserted...!!! "Twas NOT as simple as it looked on the film...

Being able to move both the fan motor holder (with the tab) AND the coil made it happen, easily...

Attempted it on my own with the aid of the video on your site, but could not remove the fan shroud due to additional copper lines that prevented me from getting it out.
Gave up and called an appliance repair guy. He had a novel approach: Don't pull the fan shroud (with motor attached) out, but instead remove one of the screws holding the motor into the bracket, then bend the bracket to get the motor out.
All good until we powered the fridge on again. Now the fan works, but spins faster (and makes more noise than) the original fan.
The repair guy's comment: "I've seen that before with some of the aftermarket fans."
Nice! I'd appreciate getting the right part when I order the part from your website based on my fridge model number.

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

Removed the fan blade then removed the motor. Replaced motora nd Installed fun blade.

Laying on my side.

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

I watched the repair video on partselect's website for the condenser fan motor and realized I could do the repair. The hard part was putting the two screws back on the bracket to mount the fan. (they were not easy to get to with your hands let alone tools) other than that super easy and great experience!
Tom

Attempted to remove whole bracket per PartSelect YouTube video. Our refrig must have been slightly older or something, because the bracket would not come out no matter how much we begged and pleaded. ~ So we replaced motor in place, which was a headache, but doable. Seems to work fine, and much quieter than the old motor.

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

I started out replacing a bad thermostat, no problem,
when I hooked up the water, I found that the water resovior had a leak.
I replaced the resovior, easy fix, but I had to buy two 5/16 brass couplers.
then I found that the box would not get below 10 degrees, and the suction pressure was very low.
I figured that the fan motor was burned out, so I opened up the access covers, the fan motor was hanging there with broken mounts, so I replaced the motor, and repaired the mount.
Everything works great now, The parts shiping was very fast, I was impressed.
I thought I was going to get away without fixing everyones
HVAC problems when I retired.
Friends and family still remember that you are the HVAC man.
Tom

Remove back cover on frig, unplug wire on fan motor, remove one 1/4 screw from top right corner of fan cage, fan cage will come out with a little twist, take note of tabs on fan cage for reinstall, remove two more 1/4 screws, take care to watch where rubber bushings are located on motor and ground wire location, fan blade will pull off of fan shalft easily, install in reverse. Very simple fix.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .