GSS20DBTC General Electric Refrigerator - Instructions

1 opened door 2. pryed cover off from cieling 3.cut and stripped wires on 4. sodered wires from old wires to new sensor. 5 insulated conection.6 put cover back on. This did not fix the problem it was the control moduel.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

took back cover off. swept the rear with a vacuum cleaner to get rid of dust.found that the fan would not turn. ordered part with your really great ordering technique. Part was suppose to be here in 3-5 days and was here the next day!!!.Removed 2 bolts pulled out the plastic clip that held the wire on. and worked the fan blade off shaft. removed and replaced in the same order as taking simple Thanks

Remove rear access cover. Remove 2 screws on fan motor bracket. Remove fan blade. Unplug harness. Insert new motor in reverse order. Literally took less than ten minutes. Plugged the fridge back in and quiet as a mouse... perfect replacement part.

Followed the video you posted on your website and it went seamlessly.
Removed the full unit and after replacing the motor - placed back in slot, secured and ran perfectly.
Hot center bar no longer a problem

Husband did the installation. Said it was easy and he had no problems with the repair. He's great at various do it yourself repairs.

I made my wife fix it.

I followed the instructions provided on the video emailed to me. I had some trouble only because my refrigerator was slightly different and it was hard to get the old condenser fan motor out. Other than that I was super pleased to have found Partselect.com. There is no way I would have been able to tackle such a major job without their step-by-step detailed help. I am enormously grateful to them. They shipped my parts the next day which is evidence of their sincere concern and understanding of the urgency of my problem. I can surely say they saved me many hundreds of dollars!

all i did was follow the video.

absolutely flawless tutorial.

the video is on the website.

I followed the instructions from the repair video that was posted in the part description. It was exactly the same as shown in the video.

Replaced evaporator fan motor, and this solved the whistling noise that had developed. Reviewed and followed the removal and installation instruction video as closely as possible. This was very helpful, with a few additions. For the model PS123NGPBBB GE refrigerator/freezer, there were a few differences from the video. There a was an additional cover panel that was positioned vertically at the back of the freezer compartment below the auger motor assembly. It was necessary to remove this cover (4 screws) to gain access to the auger motor cover screws. The unit also has a different light configuration with 2 lights. I found it helpful to remove these light bulbs and the corresponding light fixtures in order to remove the evaporator motor assembly. As mentioned in the video, it was necessary to cut the 4 wires from the wire harness of the new motor, and use butt end connectors to reattach these wires to the corresponding wires in the unit. Total job took between 1 and 2 hours, and the motor change solved the noise problem.

took down the model number, order here... got sent w/in a few days, couple of bolt/screws done!
Single mom of 6.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.