LGTR1842TP0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fred from Las Vegas, NV
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working
Took off old part and installed new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from FORT WAYNE, IN
- Parts Used:
- 242193206
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket was torn. The frig door not sealing properly
I peeled off the torn door gasket. Then installed new door gasket pushing and pinching it into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from georgetown, TN
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Water Valve was leaking water and not making ice
I unplugged the fridge and unscrewed the back cover,unscrewwd the two screws holding the water valve in place and the water line to the ice maker and the electrical connection and install the new water valve,then buttoned everything back up and plugged the fridge back in and it is working great,making ice as normal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SAN FRANCISCO, CA
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Accidentally broke the glass insert.
Simply slide the new glass insert in!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from BUFFALO, NY
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped making ice and i knew it wasnt the mechanism since I could hear that working when I unplugged and plugged the unit back on.
I found a couple of videos online of a similar product fix to get a lay of the land. When I got the part, I unplugged the unit and turned off the water. It was easy to take off the back panel and remove the old water intake valve to swap it out for the new one. Once I attached everything again I could see that the valve was taking up water but it didnt seem to be going all the way to the icemaker. I gave it some time and by the next day, there was fresh ice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from LIVONIA, MI
- Parts Used:
- 5303918634
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Refrigerator not cooling
I took out the plate that covers the evaporator in the freezer with 3/8 nut driver. I removed the clips holding on the fan cover and used the pliers to take the fan off the old motor. I then took the old motor out, affixed the fan to the new motor and replaced the motor and fan assembly. I reassembled the entire fan assembly and reinstalled the evaporator plate
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MARGATE CITY, NJ
- Parts Used:
- 240358926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Track for drawer broke and needed new tray
Perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy from OCALA, FL
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken Crisper Glass
Very easy. Watched a video on your site prior to getting the glass replacement. Removed the crisper drawers. Placed the glass in the front and placed it down. Took just a few minutes. Love your site and will come back again when needed. Thank-you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from MORETOWN, VT
- Parts Used:
- 242218602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic frame broke off
Removed glass , replace part and install glass. Simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Damascus, PA
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Warter valvr cracked
It was real easy but I still have problem making ice cubs
Fell problem is in the ice maker went it dose make cubs they don,t dump
Fell problem is in the ice maker went it dose make cubs they don,t dump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- amy from SOMERVILLE, MA
- Parts Used:
- 240312421, 5304507146, 240311303
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door sagging, creating a gap to let in condensation
You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlene from DOERUN, GA
- Parts Used:
- 240350608
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke glass on crisper
Just slide glass in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from RICHWOOD, TX
- Parts Used:
- 242252603
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The fan had stopped spinning. According to the internet it should spin freely if I use my hand, but it wouldn't.
After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.
Was this instruction helpful to you?
Thank you for voting!
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- José from ORLANDO, FL
- Parts Used:
- 242044008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge was cooling down enough the heating defrost was bad
I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl
Was this instruction helpful to you?
Thank you for voting!