LGTR1842TE0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Al from Sarver, PA
- Parts Used:
- 240313703
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Marblehead, MA
- Parts Used:
- 5303918824
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle had broken at the top where horizontal part joins vertical
The repair only involves two sets of fasteners. I am a very unskilled female repairwoman and found the top two screws easily undone with a Phillips head screw driver. I did not understand how to undo the bottom fastener which was a circle with an empty center, so I took the new handle to the local hardware store where a nice employee found me an Allen wrench for 47 cents. My only request would be that the instructions had said that was needed along with the correct size. Otherwise it went very smoothly.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door sagged, had to push the door to close it.
Used wood blocks to raise the door off the lower hinge bracket then unscrewed the suspect hinge. Cut a small shim, two layers of soda can, to place under the lower edge of the new hinge bracket and doubled the washers by using the old one to ensure I had adequate clearance for the door. After a little silicone lube I installed the new hinge bracket. All better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAT from BATON ROUGE, LA
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Water Tube That Fills Ice Maker Leaking Water
Undone the water line that comes up the back of the refrigerator and pulled the water tube out the back of the refrigerator and reinstalled the new one and reinstalled the water line. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Stow, OH
- Parts Used:
- 241796405
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice Maker not getting any water
1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- G V from Bowie, MD
- Parts Used:
- 242252603
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No ice - Replace water valve
TURN OFF WATER!! UNPLUG REFRIGERATOR!! Remove water fittings and electrical connector on old valve. Remove two mounting screws on pump bracket. Reverse procedure to install.
Was this instruction helpful to you?
Thank you for voting!