FFHI2131QP3 Frigidaire Refrigerator - Instructions

screwed the center hinge and spacer on the refrigerator then installed the center pin on the hinge and bottom door placed the top door on the pin and then screwedthe top hinge to the refrigerator,like new

Set new shelf in place and push down. Very easy!

I simply loosened the screws holding the refrigerator door handle and then slid the bottom portion of the handle off from the screw holding it in place. The bottom portion of the handle did not exactly marry-up with door, showing a very small gap. I attributed this to the age of the appliance.

Super easy fix! Used flathead screwdriver to start corner of gasket, then just pulled it out with my hands. Cleaned the track and surrounding area with a rag and some windex. Started in top right corner with new gasket and just worked my way around the door until it was fully seated in track. Done! Only thing I would do differently next time would be to start at the bottom when installing new gasket, just so I could have better sight and leverage at the end.

After pulling the fridge away from the wall and opening the paper backing on the bottom, I could see the motor. It's affixed to 3 metal ribs by 3 small screw/nuts. There is also a 12" wiring harness that led to a simple disconnect. Removing the disconnect and the 3 nuts was easy. However, there was no room to remove the motor with the fan attached. Between frame parts, the drip pan below, the ribs, and small, delicate copper tubing that can't get bent, it wouldn't fit thru any openings. So we rotated the motor inside the framework until the blade faced out, then reached in with a pair of needle nose pliers to remove the washer. Removing the washer is easy, it's just difficult to reach. With the washer off the fan was out of the way and very carefully (it was tight) the motor came out. Reverse was the same issue. Motor tight going in, not a lot of room to maneuver fan onto motor, and needed needle nose to tighten washer again. Make sure you tighten the washer before you install the motor on the prongs. Otherwise you need to remove it from the ribs, twist it to face you, then reinstall it on the prongs. Also, I felt I was stripping the nuts into the new motor. Turns out the holes in the motor aren't tapped. i realized the nuts are self tapping once I looked at them. I'm a big time DIYer and this wasn't bad at all. If your motor/fan assembly comes out whole, it's even easier.

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

Shut off water supply under the sink. Removed old valve and installed new valve. Turned water back on and within a couple hours the first batch of ice made.

took back cover off in freezer replaced fan motor put cover back works fine

Easy replacement, I did add some glue to improve hold. The new handle design was a little different and did not match freezer door so I had to change both. I guess that's why they sell as pair.

Simple instructions anyone should be able to do it.

Open door and use a screwdriver to remove screws. SAVE the screws because the new handles do not come with screws. Rotate broken handle to the left and slide the handle to the left which should slide the handle off of the screw protruding from fridge door. To install new handle, repeat this process in reverse. Rotate new handle up and screw onto fridge door.

R&R DOOR SEAL VERY EASY TO INSTALL THANKS TO ALL

The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.

If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.

In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.

Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.

Hope this helps someone. :)

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.