PLHS67EESB0 Frigidaire Refrigerator - Instructions

Ordered a new shelf which arrived very fast. Installed in no time at all as it just slides in and rests on brackets. No tools needed and the new part looks just like the original.

The old support just unscrewed & then the new one screwed right on with two screws.

Removed the Plastic Cover at the top of the door. (One Phillips Screw ) Removed the Hex Screws with socket set. Lifted EMPTIED door off bottom hinge. Pulled the broken bearing out with needle nose pliers. (Very Easy!!!) Placed new bearing into slot and reversed the procedure. 15 minutes tops. I spent more time cleaning the door and gaskets than replacing the parts. Funny thing, I called the local appliance parts store and they stated this is a common problem. However, for such a common problem, they didn't carry the part and it would have cost more than what I paid here. Additionally, I paid for 3-5 day delivery. Part was here in 2 days. Awesome!!!! I'll always come here first for all my parts needs. A+++

The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.

Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.

After removing the painters tape that was holding the previous broken part in place...

The repair as very simple. Remove the 2 screws from old cover module along with electronic plug.

Reattach the electronic plug slide new cover into slots, put the 2 screws back in. Attach the new self-adhesive cover plate...DONE!

Turn of power at the circuit breaker.
Remove the water tray by pulling straight towards you.
Remove the three screws at the bottom of the control panel.
Have someone hold the control panel while you remove the six small screws that retain the circuit board.
Gently ease the circuit panel away from the plastic frame and disconnect the six wire connector on the left hand end, followed by the two light connectors with black & red wires, then remove the four wires with spade connectors from the microswitches - noting where each goes. The control panel & circuit board can then be set aside.
Remove the three screws that retain the interior plastic frame. The plastic frame can then be eased forward taking care not to pull out the water pipe. This allows access to the screws that hold the actuators, which should both be removed. Unhook the spring & remove the broken actuator. Feed the new actuator wire up from the bottom of the frame and insert the left hand pivot first and twist gently to snap the right hand pivot into its recess. Replace the retaining plates & screws. Don't forget to the hook the actuator spring into its clip. Test the operation and ease the plastic frame back into position and attach with the screws.
Re-connect and reassemble the circuit board and front panel in the reverse order.
Power on and enjoy a glass of fresh cold water! You may need to press the reset button on the front panel to reset the lights in the actuators.

It wasn't clear how to disassemble the Ice / Water dispensing unit to get at the lever for replacement BUT the website had a great exploded parts view of the door and assembly so I was able to print that and from the diagrams you can easily work out how to pull it apart..
A bit fiddly and you need to power down the Fridge as there's 120v behind this panel (tip : dont drag out a heavy fridge, flip the breaker at the main panel to isolate the power) .

All fixed for $50 , compared to having to call out some guy who'd charge me $100 plus parts !! great deal !
Thanks !

I just took the old filter off and replaced with the new one, after I run the water for about 15 minutes and tossed the old ice and cleaned the tray.

The actuator arm was the only part that was a little difficult. The drip tray and the kick plate went on very easily. First, we went online to your schematic on the unit. This showed how it was assembled and how it came apart. We then terminated the power to the refrigerator, and removed the drip tray which exposed two screws holding in the face plate for the ice/water on the door of the refrigerator. We then removed three screws from the control panel and pulled it forward. This exposed the actuator and two more screws that held it into place. We removed them and unplugged the small plug giving power to the actuator. We then installed the new part and replaced all the screws that had been removed. We reassembled the face plate and the screws there and then snapped in the drip tray. When we turned on the power everything worked fine.

put the new ones

pushed release button removed filter, installed new filter

Ordered new water filter. It arrived, I opened it and took out the old one and put in the new one. I worked perfectly
as soon as I realized I had to remove the protective caps.

I remembered to unplug first. took the little cover off on the bottom, unscrewed the 3 screws. then just held the base that the fan is on and pulled rite off, pushed the other one rite on. it took me five min, i want to say thanks to parts select, had the part, fast shipping, great job, thank you.

First I removed one screw holding top hinge trim in place. I than removed two screws holding top hinge from refrig. I removed refrig door and laid it on a table. I than removed two screws holding the door stop and bearing hinge. I replaced the defective parts and reassembled in reverse order. Simple 10 minute repair.