FLSC238DS8 Frigidaire Refrigerator - Instructions

Not too bad, remove the water and ice bezel (3 philips screws) then remove the dispenser unit another 3-4 philips screws. Remove water line from dispenser unit (remember this as the water tube re-insertion is the complicated part) I did not remove anything other then components listed above. Seals and inner door stay intact. Replaceing the actuator and arm was easy. two small philips will free the actuator and arm. Disconnect the two wire harness (black and red) NOTE- there are two sets of black and red wire harnesses that plug in next to each other. One is for the ice dispenser and the other for the water. putting it back together is as easy as taking it apart. However the water line has no play, no slack at all so when reinserting it, the space between the dispenser unit and the door itself is limited. Put the tip of the hose down into the hole you removed it from, hold the dispenser still and use a pair of long needle nose pliers to push (feed) the hose down into the hole. Make sure it comes out the other side by about 1/4 inch to insure it is in and stable. reinstall the unit and bezel. Most of my time was spent feeding the short water tube back in place. You will see just how much room there is between the dispenser and the door before you pull the water tube from the unit. In this case you can judge if it will be too complicated for you before you go any further.

We replaced the damper, but it didn't fix the problem. We then purchased and replaced the thermistor. (We had previously replaced the defrost thermostat). The refrigerator side is now cooling better, but not enough. The damper doesn't seem to be opening. So we have now unplugged the damper and left the opening between the refrigerator propped open and the refrigerator side is now cool enough. (We had previously tried keeping the damper open before we replaced the thermistor and the refrigerator didn't cool off. So the thermistor did fix something, but the damper doesn't seem to have been the problem).

I ordered a new shelf and I put in, less than minute

The part was easy to find on the site, instructions were right on and it only took 25 minutes to accomplish with just a screw driver and a pair of pliers.

Replaced the Triple Water Valve

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.

Looked at video on how to remove and reinstall support and followed the instruct ions

It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

I had to remove the face cover to gain access to the ribbon harness, also had to remove the push pads The ribbon is a delicate item so care had to be taken not to bend the ends. The ribbon can fit either side so getting it in place to make contact was kind of tricky. After the ribbon was in, it just a matter of putting things back together. Dispenser is fixed at a minimum cost, ribbon was shipped within 2 days which was great. Thanks to Part Select for easy to find on the net, had a complete diagram of the refrigerator ice/water dispenser so finding the parts needed was simple. Doug

I removed the filter bypass from the box. I opened the refrigerator door. I put the filter bypass in the space where the filter was located. I closed the refrigerator door. I opened the freezer door. I turned on the ice maker. It worked.

Removed the fridge door, replaced plastic Hinge Bearing, re-attached door. WhaLa - No more clicking!