FFTR16B2RS0 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Rockland, ME
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
draw support broke
detached with screwdriver and applied the new one the same way. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Benton, AR
- Parts Used:
- 240535101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
top door rack was broken at the connectors
The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glen from North Tonawanda, NY
- Parts Used:
- 240535001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
no heat when drying
Replaced thermo-fuse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Apache Junction, AZ
- Parts Used:
- 241554901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Light Would Not Come On.
I removed the four bolts holding the light switch and temp knob with a nut driver, unplugged the unit and moved it to the table top. I removed the switch and replaced it with a new one. I plugged the unit back in and drove the four screws in with a nut driver and the light now comes on when I open the door. Real simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Wolverine, MI
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Right rail broken
removed drawer removed upper shelf turned upside down unscrewed old one installed new one put shelf back in put drawer back in done super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from Sarver, PA
- Parts Used:
- 240313703
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Original plastic hinge cracked across the middle
Removed 2 hex screws & old hinge, placed new hinge on cabinet & found that it didn't fit; one hole was about 1/8" off. Had to drill a new hole in cabinet top in order to attach new hinge. Hinge works fine now. I'm glad to find the hinge is metal; original one was plastic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Olive Hill, KY
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Support rail broke
I took the shelf out and took part off and replaced the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from arlington, WA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
has lights,no fan or compressor
jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!
Was this instruction helpful to you?
Thank you for voting!
Drawer Supports Broke
In 10 years, this is the second time these drawer supports broke and what a difference to fix. The parts came quickly, fit well and are very easy to install. The fridge is good as new and the cheese/condiment drawer is back where it belongs. Good quality and easy to do.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator door sagged, had to push the door to close it.
Used wood blocks to raise the door off the lower hinge bracket then unscrewed the suspect hinge. Cut a small shim, two layers of soda can, to place under the lower edge of the new hinge bracket and doubled the washers by using the old one to ensure I had adequate clearance for the door. After a little silicone lube I installed the new hinge bracket. All better now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorphial from Arcadia, FL
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drawer Support Rail Left Side Broken
The Hardest Part Was Taking Everything Off The Shelf,Took Old Part Off And New Part Popped In And I Tightened The Screw And That's It Done!Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
Broke The Draw Slide Stop Off The End Of Lft Hand Rail
Took all the item off the shelf turned it upside down on the table,worked rear off off the pin carefully,install new rail and refastened the front tab strip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cyprian J from Bradenton, FL
- Parts Used:
- 240530701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
We had a broken drawer for the lunch meat storage
No problem, got the part promptly and it was the right part and easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from apollo, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
meat drawer guide broke
take the shelf out,loosen screw,put on new rail and reattach screw,simple
Was this instruction helpful to you?
Thank you for voting!