DFHS2313MFB Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Olden, TX
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from SEATTLE, WA
- Parts Used:
- 242009604
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water filter would not disconnect from OEM Water Filter Base
Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from KNOXVILLE, TN
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker would dump ice one time and then stop. Turning the ice maker off for a minute and back on would repeat the process.
I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GROTON, CT
- Parts Used:
- 241798231
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working. Part needed to repair it no longer available so had to replace the whole icemaker.
Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.
Was this instruction helpful to you?
Thank you for voting!
I HAD 2 BROKEN BINS, THIS COMPANY HELP ME TO FIND MY NUMBER. OF PARTS
WAS SO EASY, THE PART WAS PERFECT IN SIZE AND EVERYTHING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ville from SAN JOSE, CA
- Parts Used:
- 241547902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice maker doesn’t work
Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from HOUSTON, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rail had split and would not support drawer.
Removed drawer. Removed shelve. Flipped shelve over. Removed one screw. Undid tab on each end. Removed bad rail. Replaced with new rail and reversed order. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BOZEMAN, MT
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light Switch too loose so no longer triggered by the door.
Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORMOND BEACH, FL
- Parts Used:
- 240505801
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch not working properly
After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John A from BRUNSWICK, GA
- Parts Used:
- 242252702
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
No water to ice maker
Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray from getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from LOCKWOOD, NY
- Parts Used:
- 240365401
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It was broken in the front part that hooked in the hole
Took the drawer and shelf out then took the screw out and took the old one out and then put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from CHAMPLIN, MN
- Parts Used:
- 241990301
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken hinge bearing, refrigerator door, top bearing
1. Using Philips head screwdriver, remove plastic hinge cover on top of refrigerator door.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.
2. Remove bolts using socket wrench.
3. Lift door from bottom hinge.
4. With Philips head screwdriver remove screw holding bearing in place on bottom of door.
5. Remove old bearing.
6. Install new bearing.
7. Replace fridge door using reverse steps.
8. Enjoy your handi-work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stefan from LAKE WORTH, FL
- Parts Used:
- 241786015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Removed old gasket and installed new one by pushing the gasket in the door groove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Lake Forest, CA
- Parts Used:
- 241993001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Crisper bin track support
The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches
Was this instruction helpful to you?
Thank you for voting!