DFHS2313MFB Frigidaire Refrigerator - Instructions

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

PURCHASE:
Buy the terminator from the site because they sell the
terminator (thermostat) separately. Other places have it with the
wiring harness for more money. Changing it with the harness attached
is a very, very involved project. It includes removing the entire inner
liner of the freezer. The one the site sells requires only a simple
crimp splice and shrink tube.

TEST- If you have another freezer, ice or a friend's freezer available,
it is highly recommended that the new part be tested:
You will need an Ohm meter or a continuity tester. You can make one
very easily per instructions found on line.
TEST RESULTS-
a) At room temperature. An Ohm meter should show "Open".
b) After being in a freezer or submerged in ice water for at least an
hour, the Ohm meter should show "Closed".

I have installed hundreds of defrost thermostats. Very occasionally
one is defective. This project is a bit involved, so it is wise to pre-test.

HOW TO INSTALL THE DEFROST TERMINATOR (THERMOSTAT):
A) Prep
Remove Food & Be sure the freezer is warm.
Parts need to be pried upon & cold plastic breaks easily.
Tip: Put the screws in separate cups with labels. This will make
re-installing the many components easier.
Gather tools from the attached list.

B) Unplug Unit (Turning it off is not sufficient protection against shock.)

C) Remove Light Bulb (If it gets broken while working, glass may
get in the eyes.)

D) Remove Drawers (This is a bottom freezer unit with 2 drawers)
1) ) Upper Drawer:
a) Locate the 2 rectangular boxes covering the gears. They are
on each side, toward the rear of the drawer.
b) With a nylon spudger, push in the 2 clips on each box and
lift the boxes 1/4". They will stop at 1/4".
c) At the front of each track, remove 2 hex head screws with a
5/15" nut driver or a 1/4" flat bladed screwdriver.
d) Lift the front of the drawer a small amount while pulling drawer.
Lifting allows the 2 stops on the drawer to clear the track tabs.
e) When near the end of the drawer, lift the gear wheels slightly
to clear the track.
f) Put the drawer out of the way.

2) Lower Drawer With Front Door
*Leaving the door attached makes it easier to align the drawer when
reinstalling it later. It must be straight or the gasket will gap.
a) Put a thick towel on the floor, in front of the unit, so the door
can be laid upon in without scratching the handle or the floor.
b) Pull the drawer out and look at each track about 2/3 of the way
to the back of the freezer. You will see two long, white tabs.
c) Push a tab in while pulling the track slightly forward. Firm pulling
is required. Repeat on the other side.
d) Drag the towel and door out of the way

D) Remove the air grill at the top, rear of the freezer.
1) There is a clip in the center to push with a spudger.
It is easy to see in a photo of a replacement fan bracket.
2) On the right side, in the top row of square holes, is another clip
to press with a spudger while pulling that side of the grill out.
3) On the left, there is an air chute blocking the clip. It can not be
removed. With the right side pulled free, gently wiggle & pull the
left side until the clip clears & the grill is free to leave.

E) Remove the Ice Maker (Water does not have to be turned off)
1) Loosen, but do not remove, 2 screws above the ice mold.
2) Remove the one lower screw & put it aside.
3) Lift the ice maker & store it out of the way.
4) Do Not turn any wheels by hand, nor bend the bail wire.

F) Remove the Thermistor Cover (Upper Right Back Wall)
1) Gently squeeze the sides while pulling. Stop as soon as it's free.
2) Note how the thermistor & wires are installed in the cover &
thread the thermistor free.
3) Set the cover aside.

G) Remove The back Wall
1) Remove all visible hex head screws.
2) The back wall can now be removed.
3) Set it aside where it will not scratch any surfaces, as the edges
are a little sharp

H) De-Ice the evaporator with a heat gun or hair dryer.
Don't hold the heat source in one spot for long or wire insulation
or plastic components will be damaged.

I) Note the permanent ice ball in the upper-right corner.
The defrost thermostat is under this ball. Melt it with heat.

J) Install The New Thermostat
Hint- Take the thermostat to a hardware store to buy the
correct size shrink tube and crimp sleeves (butt connectors)

removed ice denspenser and replaced spring and flap'

The repair was fast and easy .I removed the ice tray , disconnected the wiring connector and lossend two screws. I removed ice maker assy.and repeated in reverse order to install. I also installed a new water filter. I had ice in about 20 minutes.

Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!

just replaced old bins with new ones

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Installed a new Defrost Thermostat.

I removed the two side mount screws with a screwdriver and disconnected the electrical plug to the ice maker to remove it. I reversed the process to install the new one.

It was the thermostat that was the problem, but I chose to replace the entire ice maker for only $25 more.

Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.

Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.

Loosened the two mounting screws (no need to remove them), lift off the icemaker and unplug it. Reverse the order and done.