FRT21P6BSB0 Frigidaire Refrigerator - Instructions

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

Took one screw out to remove the old rail off by removing one screw placed the new one into the slot and replaced the screw and put the drawer back into the refrigerator

Just had to pop the old pieces out, assemble the new ones, and pop them in. Very easy. Anyone can do it.

Pulled the drawer out, lifted the shelf out of the refrigerator, unscrewed drawer slides from shelf and rescrewed the new drawer slides and returned the shelf, drawer, and the job was finished. Thank you so very much for your speedy delivery.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.

First removed existing damaged shelf retainer bar and end caps from freezer door. Next cut down new oversized retainer bar to size with hack saw. Then slightly opened up doubled over metal at each end of retainer bar with pliers and screw driver in order to create the small "nicks" that are needed to house the "bumps" that secure the retainer bar to end caps. Used tin snips for this. Next inserted new end caps and used pliers to crimp secure. Clipped in new assembly in freezer door.

I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

Screwdriver

I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.

Used the symptoms list, ordered the corresponding parts and watched the videos. Great company! I'll be sharing this site.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

I ordered four bearing hinges and drill holes for the hinges on top and bottom of frezer and fridge doors insert the bearing hinges on the holes and all the other part on the door were able to reversed.

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.