FRS22ZRFD0 Frigidaire Refrigerator - Instructions

Removed broke bracket. Installed new bracket (part #100). Now, everything is O-TAY!

Turn off power. Remove ice tray. Back out the two screws with nut driver and just lift ice maker off screws. Do not bend the water fill tube in the back . Now unplug the wire and remove ice maker .
To replace, match the color of wires on plug. Adjust wires in place and water fill tube and back on to the screws. Hold in place and snug screws. Turn power back on. In 4 to 5 hours your ice will start .
FED-EX UT to MN was 13 days to deliver .

had removed the doors to get fridge in thru small doorway when doors were reinstalled the elbow leak was replaced in about 15 minutes or less by cutting old elbow out of lines and the lines snap into new elbow with just a little force

Removed outside cover on door despencer, (4 screws) unplug wire, removed unit from refrig and replace rusted thru wire that holds door shut. It was fairly easy. I actually took it apart twice, once for diagnosis and once for repair after the part arrived.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

take the ice bin out of freezer. there are 2- 1/4" screws. these screws only need to be loosened a few turns. the ice maker can be slightly lifted up and will come off the screws. unhook the wire harness. take the "L" bracket off the old ice maker and put on the new one. set the new ice maker in. hook up the wire harness. put the new ice maker over the screws, tuck the wires out of the way and pull down into place. tighten the screws.

But I have back ground mechanical skills, I did see the video one time, and everything went smooth......

Looked up similar problems and found it to be the defrost timer. All I had to do was remove the plastic portion in the fridge section to get to the old timer. Popped the new one in and put it back together. Works great now. Would have been almost $150 to have a repair company come out and fix it.

i removed rhe old storage drawer from the refrigator. removed the front face and slid it on to the new drawer i received from Part Select. put the drawer into the refrigator and it fit perfectly. Part Select web site worked perfectly on selecting the right part. the part was delivered in three days. i would recommend this company for your appliance replacement parts and would not hesitate ordering from them in the future.excellant service.

tony
scottsdale,arizona

The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)

Changed the defrost timer and the Thermostat. Still did not fix the problem. Replaced the defrost heater and now it's cooling just like new.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

I took everything out of the freezer. Removed All the shelves, took the front off of the evaporator coil compartment. Then I defrosted the evaporator coils with a blow dryer because they were basically a solid block of ice. Then removed the heater coil, installed a new one. Installed a new defrost thermostat. Put the evaporator coil panel back on. Then I turned the thermostat back up to where the fan came on and I noticed it took a few times for the compressor to continue to run. I don’t know what that was all about but eventually the compressor kicked in and everything worked like it should.

I replaced the water pressure valve, unplugged the power , turned the water off, took off the back cover, loosened the screws holding the valve on , disconnected the water lines, and replaced with the new valve and reassembled water lines and remounted valve, done.