FRS22ZRFD0 Frigidaire Refrigerator - Instructions

I put the refrigerator and saw that the fan wasn't working so I change the fan and the problem still the same. I order a timer and thermostat and change them, nothing change so I order the capacitor and when I remove it I saw that the relay swith was burn out so I order a switch and evarything is ok.
The problem when the fan broke the compressor overheat and burn the swich.
I learn a lot and still saving money over these repair guy.

Thanks

I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.

Twisted replacement bulb into place easily. Let there be light!

Used pliers to remove filter.

it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.

I removed the old housing (three screws) , pulled it out about three inches and discounnected the two water lines. Then I put the new one on, attached the two water lines & I had water immediately & ice within a couple of hours.
Really it was a no brainer, but I'm sure I saved at least $50 doing it myself.

Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.

the heater defroster was bad. tested and no continuity brake in eliment.just doing a visual might have detected it but it`s hidden behind the coils.....all is working now

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Removed old thermostat and replaced. really easy.

Ordered parts, and replaced them. Living in Alaska it made the shipping take a little longer but they arrived and now the top hinge dosen't pop out, door shuts nicley and we were able to turn the temp. control down which in the long run will save electricity.

Wasn't sure if it was the derost timer or the heating element. Since the timer was much cheaper, I bought it and crossed my fingers.
My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring.
Success! My coils no longer freeze up.
Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.

Discovered water filter housing broken allowing water to leak out when using water in door function.
Found part number using Part Select diagrams. Ordered part from Part Select,. shipping time about 3 days.
Removed 3 screws houlding from cover over housing assembly. Removed cover, removed old, broken part by pulling water lines from top of unit. Replaced new housing in place, connected above mentioned water lines, replaced cover and holding screws. Tested for leaks. Everything worked great.

The longest part of replacing the drawer was swapping all the veggies out of the old one. No tools,slid the glass drawer front from the old one and slid it into the new one.

After posting the specific symptoms and getting feedback, I had narrowed the cause to two linked parts. I ordered both intending to replace first one, then the other as needed. With parts in hand, I pulled off the freezer control knob, used a nut driver to remove the two panel securing screws (behind the face, against the inner ceiling) and gently dropped the cover down. The control (temp sensor and cold control) is easily accessible as it sits wedged into two slots in the plastic cover. The control must be slightly lifted in order to extract the long sensor that attaches to the control and runs under it and into a plastic sleeve behind the panel (the new control comes with the sensor wrapped in a tight coil and it must be unwound for the install). Removed the three wires noting which color goes where. Used needle-nose pliers to remove the small push-on tabs and removed the control. After starting the new sensor probe into the sleeve re-attached the 3 wires to the new control. Used the original as a model for how to pre-bend the probe for the first 2 inches as it was mildly frustrating to position the unit back correctly. Pushed everything back into place, re-installed the screws and plugged the fridge back in...(you DID unplug it first, right?). Still haven't used the second part (defrost timer), but I expect it to go soon...it is a 17 year old refrigerator, after all.