FRT17G4AW1 Frigidaire Refrigerator - Instructions

First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

First removed existing damaged shelf retainer bar and end caps from freezer door. Next cut down new oversized retainer bar to size with hack saw. Then slightly opened up doubled over metal at each end of retainer bar with pliers and screw driver in order to create the small "nicks" that are needed to house the "bumps" that secure the retainer bar to end caps. Used tin snips for this. Next inserted new end caps and used pliers to crimp secure. Clipped in new assembly in freezer door.

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!

Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

The refrigerator that came with the purchase of my house had a missing retainer bar in bottom shelf of fridge and a duct-taped retainer bar in freezer. When parts came, all I had to do after removing the duct-tape, was slide up the broken end cap to pop it off then, snap the retainer bars into the end caps and slide them down into place. No tools necessary. Should have done this two years ago when I bought the house!

Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)

I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.

I just took off the broken piece and replaced it with the brand new piece I got from Partselect.com. The part was like three bucks and shipping was a little over 5. I fixed the bottom shelf for under ten bucks. I didn't think I'd be able to find the part on the net, but a quick google search led me here. My wife was always nagging me to fix it. The duct tape I used just wasn't good enough for her. Now, with partselect.com I made her dream come true! David Bueno-Hill

I started look inside ,disconnected power, and open all possible compartments to see any burned part. Fortunately I fined a small part look like melted and then i went online and make my research .Then i ordered that part and change it.

This is super easy. You just pop the old supports off vertically, pull the bar off of the broken one(s), replace them with the new one(s), then pop the whole thing back onto the door of the fridge by pushing down on both sides.

My upper and bottom air diffuser was missing.
Purchased both air diffuser and placed it.