MRS22HRAW2 Frigidaire Refrigerator - Instructions

Took out the broken one, cleaned the frigi, guided the new frame into the mounting hole. It's was very easy and the help video really helped: both for finding the right part and once the parts arrived, step by step procedure.Thank you.

I used a pick to remove the lugs from the old starter. Clicked them right in the new one and it went to woking!!!

Simply removed drawer from refrigerator, slide the front door off old drawer, wash new drawer & old door, slide door into place on new drawer and replace in fridge.

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

real easy with the help of the video , made the difference

I went on partselect put in make and model number, a list showed the probable cause. I watched the how to video. When I received the part in short order I loosened 2 screws disconnected the wiring plug (sprayed it with contact cleaner) pluged it in, removed screws from old part put them in new one. Put timer back in its location and tightened the screws. Very eazy, works fine.

I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

After receiving the replacement drawer from PartSelect, I removed the broken drawer and took off the front (since the drawer is sold separately). It came off easily with a putty knife. I cleaned the front (clean every 10 years whether it needs it or not), slid it onto the drawer, used the putty knife to reattach the lip and slid the drawer into place. Took ~3 minutes. There is a very good short video at the website if you are unsure about removing & attaching the front piece.

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

The ordering process was great and the package with the upper and lower drawers arrived on time. I watched the video and was ready to go. I loosened the front of the drawer as instructed, but I couldn't get it off. Finally I realized that the front was "glued on" by the accumulation of years of use. I sprayed it with 409 and the two separated just like they were supposed to. The rest of the process went easy -- just like the video said. When I changed the second drawer, I sprayed it fist and the process was really simple. Thanks for your service and for your instruction video.

Followed instruction vedeo from partselect. THANKS!!!!!

unplugged frig,removed bottom front cover and loosend 2 screws at bottom front left and slid defrost timer out from behind metal panel,unplugged the old and plugged in the new.frig works great.

Replacement parts fit perfectly. Simply removed the broken frame, place existing glass in new frame, and set frame in back wall mounts, then lower frame to side existing side mounts. Insert new drawer in the new frame. Worked great.

I followed the procedure online and found the thermostat was ok, it had continuity when cold, and the heater coil was also ok, it too had continuity, therefore the problem was a bad defrost timer. the refrigerator works great, thanks parts select!

The process was very simple, slid the front off of old drawer and slid the front on the replacement drawer.