MRS22HRAW2 Frigidaire Refrigerator - Instructions

I received the drawer within 2 days of ordering it online, which was extraordinary. I removed the front of the old drawer, as instructed and placed it on the new drawer. I then replaced the drawer in the refrigerator and the job was complete. The entire experience from beginning to end was simple and completed in very little time. Had I known it would be this easy, I would have ordered the drawer sooner.

I didn't know the front of the drawer could come off so it was pretty gunked up with dried meat juices that had leaked. The fit was very tight. I had to really work the putty knife to get it between the front and the drawer at the bottom where the catch is. I was afraid I would break or chip the front before I got it off but it handled the pressure pretty well. Had to use some force though. Once I cleaned the front it slid right down and snapped into place.

Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

took door off. sanded rusting hinge and greased. installed door hinge washer. I had to install a larger washer over hinge bearing to help support the door where it was rusting. no sweat. works like its new. thanks to you guys for having the parts.

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

The job was as simple as could be pry away the old and push in the new.
Only wish I had done years ago. Tthis is a great service to customers.

just like the video showed...it was excellent!!!

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

The replacement of the Drawer Cover support was simple, it snapped in to the existing holes. You had said you did not have a replacement for the crisper drawer cover but the storage drawer cover was identical and I ordered it, and snapped the adjustable vent off of the old crisper onto the new storage drawer cover and all was well. The parts arrived in two days without expedited shipping. I couldn't be happier.

first I replaced the timer control hoping thats the problem,unfortunately situation the same ice build up on the freezer.so I replaced the defrost thermostat.right now I'll still observing the condition if still the same.may be in couple days.so far its good.and to replace the parts is not difficult and easy.

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

Took out the broken one, cleaned the frigi, guided the new frame into the mounting hole. It's was very easy and the help video really helped: both for finding the right part and once the parts arrived, step by step procedure.Thank you.

I order defrost timer then replaced it but it seemed doesn't work. I order defrost thermostat again then it worked fine until now. Thanks. Part selects.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.