LFSS2312TD3 Frigidaire Refrigerator - Instructions

I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23

Removed evaporator cover and dismounted evaporator coil. Threading in the new heater was difficult but not impossible.

The repair went easily after watching the video, took me less than an hour to complete the repair.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !

Called "local" repair warehouse and ordered part. They shipped the wrong part. Went on-line to Part Select and got the right part.

I changed the defrost thermostat and the heater.

DID IT JUST LIKE THE VIDEO SHOWED. UNHOOKED ELECTRICS, CUT TUBING, HOOKED UP ELECTRICS THEN TUBES TO NEW PART. PIECE OF CAKE.

Followed install instructions on utube. Once freezer was empty, back panel was easily removed, and defrost thermostat was in plain sight, and easy to replace. Hope that solved my problem. Refrigerator has been plugged in for four days now, and is cooling properly so far.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

I bought and replaced the control board as suggested. It didn't help. It was suggested that it was the Damper [lets cold air from the freezer into the refrigerator side]. I bought a new Damper unit. It didn't help. It was suggested that I replace the temp sensor[s]. I replaced them both, and the HI alert disappeared, but it did not help with cooling the refrigerator. I gave up after spending $400 on parts with no solution; I bought a new double-door refrigerator.
Note .... None of these parts come with any instructions. You have to watch youtube.

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

Basically unhooked water lines and removed the screws

Had to replace with a whole new part, had to take it all apart to replace