FRTG16X6AW1 Frigidaire Refrigerator - Instructions

removed top shelf from refrigerator, and placed it upside down on counter. removed 1 screw from old track and track was out. put new track in place, put in screw and replaced shelf

I just put the new one in with no problem

Ordered the right parts thanks to your list of part numbers and where they were located on the refrigerator. They fit perfect and problem fixed in five minutes. This is the best site I have ever used!

Please keep up the good service you provide.

Easy peasy... took the shelf out of the fridge. Unscrewed the old rail. Screwed in the new one. Put the shelf back in. DONE!!!!

My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.

Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!

Thanks

Simply removed screw from old rail, inserted it into new rail and connected the rail to the old shelf. A very easy fix and a money saver. Local techs wanted $75 just to come out and look at the problem. Local parts places didn't stock the part and gave an estimated delivery time of 3-5 weeks with a price $12 higher than you guys. I received the part from your company well within the promised maximum 5 day delivery time - 3 days! Thanks, you have a repeat customer.

I slid off old caps, then slid on new caps. I pushed down metal holding clamps and I was finished. The whole process was about 5 minutes. The parts select web site was great. I looked up my parts on the easy to use catalog and ordered them. Make sure you save the broken parts or write down the part numbers to make finding your exact parts easier. I wish all parts web sites were as easy to use as parts select.

new drawer was received within 2 days and was extremely simple to install.

A single screw holds the part in place. The ONLY challenge is seating the new slide so that the screw hole in the glide matches the hole in the support assembly. Initially setting the glide into place mismatched by about 1/16 of an inch toward the back of the refrigerator. Firmly grasping the new part after mating it to the two receivers on the support assembly, pull it toward you until it clicks into place. The screw should mate cleanly to the new part without any difficulty. Make sure you get the right or left side part, as they are not interchangeable.

It simply snapped into place. No tools required. A very simple repair.

The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.

Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.

ordered brackets - epoxy glued all door shelf parts. When dried I snapped in place and then used self tapping screws to give added support to brackets to the door. Draw guide - replaced part and screwed in as directed.

I had to cut the retainer bar to length and then snap the end caps onto the bar. Then just snap the assembly onto the freezer. No problem!

replaced with new drawer support rail and put drawer pack in refrigerator

I cleaned off the shelf that the drawer hangs from and removed it from the fridge. I took the philips head screw from the back of the broken support rail. Put the new one on, screwed it in and replaced the shelf and drawer.