CFHT1513LZ7 Frigidaire Refrigerator - Instructions

I unscrewed the top of the handle that was still attached to the door and replaced it with the new handle and really made sure the bottom screw was tight and then positioned the top holes and screwed them into place. VERY EASY!!!

took the old one out, put the new one in. Will be an ongoing problem due to the flimsy nature of the rack. Refrigerator is in a rental unit. Great to know parts a just a phone call away, and arrive super fast.

Watched the video to see how it was done. Removed the two screws on top of the broken handle and remove broken part. Slide bottom of the handle on to the screw and replaced the two screws on top handle. Presto...all done in under five minutes. Ready for my next project.

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.

My unit was not defrosting. Defrost heater was not functioning. Defrost heater tested good with a meter. Thermostat (cold) tested bad with a meter. Defrost timer was working properly. I replaced the thermostat but I had to buy red crimp connectors because the blue ones that came with the thermostat are designed for wire bigger than 18 AWG wire. The thermostat leads as well as the wire in my unit were 18 AWG. The crimp was not tight enough for my liking with the blue butt connectors. I also purchased smaller heat shrink tubing. After replacement, the defrost heater started working. I could see it glowing. Unfortunately immediately after getting the heater working the contacts in the defrost timer arced and stuck together thus preventing the timer from exiting defrost mode. The heater went off at this point indicating that the thermostat was now working. I then purchased and replaced the defrost timer and now the fridge is functioning properly. I noticed both replacement parts, even though I looked up my fridge model, were different part numbers than the originals. I'm guessing the new parts are improved? I also noticed the timer was an 8/30 rather than a 10/30 like the original. The fridge is working better than when it was new so evidently defrosting every 8 as opposed to every 10 hours is better for my unit.

Long story short:

Buy the correct crimp/butt connectors before beginning replacement of the thermostat and proactively replace the defrost timer since it is rather inexpensive.

Unscrew the attached broken piece from the refrigerator (two screws). line up the new door handle with the existing screw holes and attach. Simple.

took off top screws I slid the bottom of handle on an angle then turned handel to the top of the door and replacedthr screws all done

Take down the light assembley by removing the 4 one qurter inch screws, and install the diffuser where it belongs.

Replaced the handles looks alot better love them. Thank you ! :)

The new part fit perfectly! I just snapped it on! Thanks so much Partselect! You processed my order quickly, and I had it in my hands in a few days. What a relief to have this fixed! Thanks again.

simply backed out 2 screws on each of the handles, then by observing the key ways in the new handles, i realized all i had to do was push down on the old handles to release them. then it was a snap to slip the new handles in and secure them with the original screws. SO EASY!

Thermostat assembly, remove light bulb, remove 1 screw, drop thermostat casing, two screws to remove timer from inside and install in reverse. Old Timer had electric motor and lasted 30 years. New one looks to be electronic with plastic motor gears.

I hesitate to say anything since I did exactly what their video told me to do, and it fixed the problem. Couldn't be happier. Was positive I was looking at 1000$ for a new fridge. Love being able to fix it by installing 15$ part myself. Thanks guys.

The repair literally takes 5 minutes...and that included 2 minutes to find my Phillips screwdriver. Save a ton of money, and do simple repairs like this yourself.

remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test