CFHT1513LZ7 Frigidaire Refrigerator - Instructions

Glued and taped old door rack until new part arrived. Perfect fit.

Very easy to do, as per the video instructions.

I removed the four bolts holding the light switch and temp knob with a nut driver, unplugged the unit and moved it to the table top. I removed the switch and replaced it with a new one. I plugged the unit back in and drove the four screws in with a nut driver and the light now comes on when I open the door. Real simple!

Screwed in three screws. Easy!

the replacement handle did not match and does not lay flat against the door.other than that problem it waas easy

No tools were required to install

Snapped new door rack into place.

remove two screws, turn old handle 15 degrees, pull off old handle.Insert new handle onto bottom screw, turn back 15 degrees. insert and tighten two top screws and its done. This took less than 15 seconds to replace.

So very easy. I couldn't believe how quickly the part arrived and how easy it was to install.

I got the model number and because you offered diagrams I was able to order the correct replacement. The piece slid right in and I thought it was miraculous. It was so easy.

I unscrewed the top of the handle that was still attached to the door and replaced it with the new handle and really made sure the bottom screw was tight and then positioned the top holes and screwed them into place. VERY EASY!!!

Watched the video to see how it was done. Removed the two screws on top of the broken handle and remove broken part. Slide bottom of the handle on to the screw and replaced the two screws on top handle. Presto...all done in under five minutes. Ready for my next project.

took the old one out, put the new one in. Will be an ongoing problem due to the flimsy nature of the rack. Refrigerator is in a rental unit. Great to know parts a just a phone call away, and arrive super fast.

My unit was not defrosting. Defrost heater was not functioning. Defrost heater tested good with a meter. Thermostat (cold) tested bad with a meter. Defrost timer was working properly. I replaced the thermostat but I had to buy red crimp connectors because the blue ones that came with the thermostat are designed for wire bigger than 18 AWG wire. The thermostat leads as well as the wire in my unit were 18 AWG. The crimp was not tight enough for my liking with the blue butt connectors. I also purchased smaller heat shrink tubing. After replacement, the defrost heater started working. I could see it glowing. Unfortunately immediately after getting the heater working the contacts in the defrost timer arced and stuck together thus preventing the timer from exiting defrost mode. The heater went off at this point indicating that the thermostat was now working. I then purchased and replaced the defrost timer and now the fridge is functioning properly. I noticed both replacement parts, even though I looked up my fridge model, were different part numbers than the originals. I'm guessing the new parts are improved? I also noticed the timer was an 8/30 rather than a 10/30 like the original. The fridge is working better than when it was new so evidently defrosting every 8 as opposed to every 10 hours is better for my unit.

Long story short:

Buy the correct crimp/butt connectors before beginning replacement of the thermostat and proactively replace the defrost timer since it is rather inexpensive.

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.