FRSR25V5AQ3 Frigidaire Refrigerator - Instructions

turned ice maker water off.Removed housing with 1/4" nut driver.disconnected water lines that had quick disconnect.(pushed bottom plastic washer up & popped off.unscrewed old filter cup off with nutdriver. Screwed new one in place,put filter in cup & screwed on,pushed water lines on.put housing back on & turned water on. No leaks & had my ice maker back in working order,also my water on front door.was easier than expected.lady was very helpful when ordering cause I was worried it may not be same one cause was slight difference in appearance.but it matched up to model number & ended fitting just fine,also was shipped very quick,1 day & it was at my door.nice to have ice again,thanks part select.

Took door off and replaced part and door back on...... easy!!

Exposed and removed the screws at the top of the door. Removed and replaced the bearing and plate on the bottom of door and put it back together. Honestly, this is the easiest repair I ever made. The biggest chore was removing the contents of the door before taking the door off. Also was working alone, an extra pair of hands to hold the door would have been helpful but not necessary.
Be prepared to never hear that horrible clunk again!

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

watched the video, ordered the part and handed it to my husband. He quickly removed the hinge cover and took it apart--the lower door bearing was tightened with glue which made it difficult but once that was out of the way, it was remove, assemble and back in business. Thanks for making it "do-able". C and D in New Mexico.

First removed 3 bottom screws on ice dispencer, unpluged the wires then pulled unit out of door. Then removed 2 flat pivot brackets, changed the actuators, then reversed the assembly. On the support studs, were pryed out of side walls and the new one's inserted, used a very small hammer to drive the pin's on the studs.

I removed the refrigerator door by removing the two screws on top, I layed the door on it's side and removed 2 screws on the bottom to remove the broken part. I installed the new part, installed and tightened the screws. I then installed the door in place. It was an easy repair.

Emptied contents of door. Removed door by removing top hinge. Turned door upside down. Removed broken hinge bushing and installed new one. Reinstalled door and top hinge. Door works perfectly.

My hubby and I simply lifted the door up and out of the hinges and while, balancing the door on a footstool, took off what was left of the old closure bearing, stuck the new one up inside the hole and placed the door back down on the fitting. VERY EASY!

The most important thing to remember is to empty the door of all items. The following are the next steps: 1) Remove plastic cover on top hinge bracket. 2) Remove 2 screws on top hinge while holding the door so that it does not fall away. 3) Pull the door up and out. 4) While door is on its side make note of orientation of broken piece and then remove the broken hinge from the inside corner of door. You may need your pliers to help remove the broken plastic. Try not to push the old piece into the door. 5) Once the broken piece is removed just insert in same direction as the broken one was. Now reinstall the door in reverse and your done.

My dad actually did the repair when I wasn't around but he said it was a piece of cake. He first just tried to replace the cup portion but ended up removing the entire filter housing. He found a large crack on the part that the cup screwed in to. His recommendation is to make sure that the water to the fridge is turned off so that it doesn't leak all over the place while you change out the parts.

removed the 2 screws then the housing. Then i removed the 2 hoses that are connected to the filter cup.Replaced it with the new one then i connected the water filter .

Removed Fridgedoor and doorstop with Bearing-Hinge and replaced with new Parts. Reattached
Door,took about 15 minutes to do.

It took me longer to find the the right socket fitting...
I then removed the screws and water line fittings. I then replaced everything just as i had removed it.
EASY!!!

Watched the video on YouTube and followed the instructions.