FRSR25V5AQ3 Frigidaire Refrigerator - Instructions

Removed old ice maker , emptied ice into new ice maker and installed ice maker, it took less then 2 minutes to complete job and no tools needed , this was the easiest repair I have ever done.

Thawed out freezer, I recommend laying a couple old towels in freezer to soak up melted ice. Replaced old thermostat with new part. Removed 2 screws, removed back plate, unplugged 2 connectors and cut 2 wires. Crimped in new thermostat and repositioned to original part location. Reconnected plugs as I reinstalled back plate. Installed 2 screws and connected power. Works like new! Trouble shooting and part installation video is very helpful, great site!

first removed three screws holding cover un snap water lines remove two screws holding filter housing up reinstalled new parts

Took out the out one and slid in the new one so easy to do

Wasn't sure what parts to replace so happy to find intact entire assembly. Popped out the old, popped in the new. Back in business in less than 5 mins. Highly recommend.

I was able to replace the housing by only removing the front cover, the e-ring and washer and the 3 hex-head screws. I was able to work the old housing around to get the actuator arm off and then get it properly inserted into the new housing. Attach the new housing, IMPORTANT: make sure you get the fixed-blades and spacer assembly in the slot of the housing that holds them in place, replace the e-ring and washer, check that the actuator arm operates the door properly and replace the front cover. The videos can be helpful but these shortcuts will save some time.

took off bottom plate to water/ice dispensor, removed three screws, took off front plate, removed three screws, unpluged water connector, removed two screws holding down water actuator where it pevits from and then replaced with new to find out the new part was off white vs white, does not look to good.....

The part arrived in about 2 days! The right side support that is attached to the inside wall of the refridgerator, that holds the crisper guide, broke apart and would not support the crisper. We took everything off of that shelf and took out the crisper and the glass that is on the shelf. We then carefully pried the support from the interior wall (it was a slow tedious move to be sure we did not damage the wall of the fridge). We made sure all of the pieces were out and snapped the new one into place. For some reason the old one did not want to come out. It broke into many pieces and we carefully pulled all of the little pieces out of the notches

Remove filter housing cover (one 1/4" hex screw). Remove the quick disconnect water lines. Replace filter housing with new (two 1/4" hex screws). Reconnect water lines. Reinstall cover.

i ordered a replacement, and when it came in i took the old part off and installed the new dispenser. it works great.

Remove the food items from the shelves on the door, Phillips screwdriver to take the top cap off. Adjustable wrench to take the two screws off the top hinge. Lift out the door and set aside. Remove two bolts from the lower hinge, reinstall with the new hinge and spacer. Reinstall door on lower hinge. Lift into place to reattach the upper hinge. Put the food back in and you're done.

Removed ice bucket from freezer. Remove ice. Remove 2 phillips head screws from the inside front of ice bucket, and 2 fromt the bottom front to remove the front cover. Remove the E clip and washer from ice crusher shaft. Remove 4, 1/4” head screws from ice crusher housing. Unclip the selector shaft from crusher door paying attention to position.Slide housing off of shaft and discard. Install new housing over shaft and install the 4 screws. Install selector shaft into door. Install the E clip and washer onto shaft. Install front housing with the 4 screws previously removed. Refill bucket with ice and install bucket back into freezing taking care to orient the ice screw shaft into the cog in the back of the freezer as well as the door selection shaft. Test operation.

Open freezer
Pry the switch out (bottom first, then push the tab on top while prying out)
Move wires to
New switch
Push switch in
Test

Very simple installation.Gentle pull out on the old Ice Container and Auger Assembly.Take the new Ice Container and Auger Assembly and slide in place.Make sure everything is lined up.

Installed new Auger drawer assembly