KSPZ25V9GS3 Frigidaire Refrigerator - Instructions

Just a firm twist on the covering and insert new filter. This is the second time in 2 weeks that I have ordered parts from PartSelect. The best service I have ever had. Recieved parts the next day.

ordered the part, watched the video....it was a snap

My Frigidaire Drawer broke... I ordered the parts and installed it within 5 min. It took more time to remove the food and drawer then it did to install the pegs.

Took out the support and put back in the new one.

Replaced filter. Very quick shipping, was very happy to get is so soon.

Just pluged it in

The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

Because of the design of the support, this could have been a difficult job. However, with the video that was provided when I selected the part, it was not a problem. All you have to do is knock the center pin through the support and remove the old support. Pull the pin out of the wall of the unit and push the new support in and drive the new pin in until it is flush. That's it!

Undone the water line that comes up the back of the refrigerator and pulled the water tube out the back of the refrigerator and reinstalled the new one and reinstalled the water line. Done

Pull out the old clips,that were crack.The new ones are hanging off.I don'nt know if i should put some kind of glue,or something.To help it stick on.

Replaced the ribbon from circuit board in door to the circuit board which controls the water and ice dispenser and back light. Unplug the refrigerator before any repair is attempted. You can short the boards when replacing the cable. Remove the front plate where the buttons are. Be careful, it slides up then out. once you remove the outer panel, you will see the ribbon which attaches to the front panel to the circuit board in the door (of course freezer side). on the plate you just removed, there is a white cover plate secured with four small philip head screws. Don't try to replace the ribbon without removing this cover. If you do, you run the risk of breaking the the ribbon and then you'll have to order another one. Make sure you note which way the cable is inserted. Insert the cable in both slots on the door and panel. Replace the screws and front panel.

i dissasamble the water & ice dispenser and substitued the ribbon cable for the new one.

Turned off the refrigerator, removed the bottom drawer from refrigerator, then removed the glider bars for the drawer on the left side where the filter chamber is. Removed the filter and then removed the plastic peace guarding the filter chamber. Once that was all removed we removed the screws holding the filter base in place. Now that everything was exposed we removed the inlet and outlet lines from the filter base by pushing in the nobs inside the base and pulling the lines out with some slight elbow grease. After that we just proceeded in reverse. We plugged the filter in after the base was secure to make sure that the fix worked. The repair worked like a charm, was relatively simple and now our fridge is all better with water and ice without a large repair bill :o)

Crusher housing had broken so I ordered the part and replaced it. I have since put it back together twice. When I first installed it it crushed the ice no problem. From that point on it seems to lock up and won't crush the ice, cube ice works but the blades seems to hang up after the first use. I can turn the cog by hand but I have to turn it backwards a few times before it turns freely, however it still won't crush the ice. I took it apart and put it back together again. Same thing happened after the first time I tried it. Can you help me. The old crusher broke into. Could something else be locking up?Thanks for the help