Models > KSPZ25V9GS3 > Instructions

KSPZ25V9GS3 Frigidaire Refrigerator - Instructions

Jump to:

All Instructions for the KSPZ25V9GS3
61 - 75 of 215
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Pete from THE PLAINS, OH
Parts Used:
241885001
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Dispenser Crusher Housing was broken
I followed the instructions, my ONLY issue was about the Part 46 the Ice Dispenser Actuator Rod. The front of the arm has flared out grooves and it didn't warn me about making sure the rod is properly aligned thru part 23 Front Plate or else when the ice maker actuates the rod it will not move properly if the grooves are not aligned on each side of the Front panel. I hope you can understand what I mean, if not just look at how the Part 46 rests in Part 23
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sam from Ravenswood, WV
Parts Used:
241850615
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Not making ice
Took out old replaced with new. Now it makes ice
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Curtis from ROCK HILL, SC
Parts Used:
241885001, 241684901
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Ice Crusher Houseing cracked broke into pieces
Remove ice drawer ,Removed front of drawer 4 screws ,Removed broken crusher 3 screws Ordered new parts reassembled replaced fix blade spacer that was broken and blade cover housing reattached front of drawer !
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from Newberry, SC
Parts Used:
5303918202
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
the freezer frosted up and the fridge was not getting cold.
I watched the instructional video and did what it said.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Laura from Westville, OK
Parts Used:
241685101
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
The center of the plastic auger drum was broken
Had to replace with a whole new part, had to take it all apart to replace
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from INVER GROVE, MN
Parts Used:
241885001
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Every part of the ice crusher (blades and housing) bent/broke in successive failures
This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MICHAEL from CINCINNATI, OH
Parts Used:
240363702
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
A Door Bin On My Refridgerator Broke On Christmas Day From Stuffing It With Wine
Just popped the new bin into place with my thumb. I also wanted to say. . . Don't bother with express or overnight delivery. I ordered the new bin on a thursday, paid for 3-5 day delivery and it arrived the next day. Installed it in less time than it took me to unwrap it.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Veronyka L from BREWTON, AL
Parts Used:
WFCB
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
I twisted off housing and removed used filter.
I placed a bowl under the filter to catch drips. I wrapped two rubber grippers around the housing and twisted to the left with all my strength. (I am a weak woman). I removed the used filter and inserted the new one. I used the grippers again to replace housing over the new filter. Voila! All done for 6 months.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from PHILADELPHIA, PA
Parts Used:
5303918202
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Evaporator was freezing up and was running non stop
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
W Howard from KEENE, NH
Parts Used:
240396102
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old part broke
The original part broke. The plastic attachment end of the part snapped off. The new part was easy to attach.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from WEIRTON, WV
Parts Used:
241885001
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Plastic gate to redirect ice to the crusher broken off
Removed ice maker bin...removed screws and housing and reinstalled all...very easily completed.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from MONTGOMERY, IL
Parts Used:
5303918202
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Coils frozen over. Refrigerator not cooling
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Salvador from SANTA ANA, CA
Parts Used:
5303918202
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Freezer worked, refrigerator didn't. Ice build up on coils.
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kelly from Comfort, TX
Parts Used:
241993001
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
shelf supports broke
just slid them in and gently taped the pegs in
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Florence, CO
Parts Used:
241993101
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Drawers wouldnt open
Replaced wall pins pulling center pins removeing set new ones replaced drawers. Damm Kids Busted the old ones it was easy to find your web site , parts and purchasse items as this was a new one It was diffacullt to use drawers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KSPZ25V9GS3
61 - 75 of 215