FRSS2623AD2 Frigidaire Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- nathan from Buckley, WA
- Parts Used:
- 241657502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Installed a extra shelf
Pushed the shelf pegs in the wholes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Saranac, MI
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Seal was broken
Pulled out the old seal by hand. Cleaned the opening. Pressed the new seal in place. The entire process took about five minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orlando, FL
- Parts Used:
- 241786013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Torn fresh food door gasket
Removed the old gasket and installed the new one. Really, really easy to do. Took me about ten minutes.
Was this instruction helpful to you?
Thank you for voting!
old seals on both fridge doors
pulled the old seals off one at a time and starting from the top of each door, pressed the top edge of the seal into the groove, using the quik clamps to hold the top in palce at each top corner, went down each side of the door and pressed the seal into the groove, when I reached the bottom, I moved the clamps to the bottom and used thm to help press the seal into the bottom groove, Each door took about 15 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Allegany, NY
- Parts Used:
- 241885001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The ice crusher flap was broken.
Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from chatsworth, GA
- Parts Used:
- 241685101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
ice maker would not dispence ice
took ice maker out empty ice removed 6 screws removed auger out took off lcck nut pulled off drum replaced with new drum reassembled.
Was this instruction helpful to you?
Thank you for voting!
The drive blade was worn and wouldn't turn the drum
First off make sure you have a good quality Phillips screw driver. When the blade is worn out you can disassemble the ice maker with out removing the front. But to reassemble the front cover must be removed. Do yourself a favor and buy the drum and nut also. I am a mechanic by trade so the tools and repair was really easy. Be careful of the ice crusher BLADES they are very sharp. If your not mechanically inclined take pictures before disassembly, that will help you greatly. Hope this helps someone. Thanks Rory
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Philadelphia, PA
- Parts Used:
- 241684503
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
the drive blade for ice maker was rusted
first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Hockley, TX
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Stop crushing ice.
Crusher housing had broken so I ordered the part and replaced it. I have since put it back together twice. When I first installed it it crushed the ice no problem. From that point on it seems to lock up and won't crush the ice, cube ice works but the blades seems to hang up after the first use. I can turn the cog by hand but I have to turn it backwards a few times before it turns freely, however it still won't crush the ice. I took it apart and put it back together again. Same thing happened after the first time I tried it. Can you help me. The old crusher broke into. Could something else be locking up?Thanks for the help
Was this instruction helpful to you?
Thank you for voting!